Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Infiniti FX50FACTORY OEM SERVICE PROCEDURE
Data Monitor Mode
MONITORED ITEM LIST
| Monitored item | Unit | Description | Remarks | ||||||
|---|---|---|---|---|---|---|---|---|---|
| ENG SPEED | RPM |
|
|
||||||
| MAS A/F SE-B1 | V |
|
|
||||||
| MAS A/F SE-B2 | |||||||||
| B/FUEL SCHDL | msec |
|
|
||||||
| A/F ALPHA-B1 | % |
|
|
||||||
| A/F ALPHA-B2 | |||||||||
| COOLAN TEMP/S | °C or °F |
|
|
||||||
| A/F SEN1 (B1) | V |
|
|||||||
| A/F SEN1 (B2) | |||||||||
| HO2S2 (B1) | V |
|
|||||||
| HO2S2 (B2) | |||||||||
| HO2S2 MNTR (B1) | RICH/LEAN |
|
|
||||||
| HO2S2 MNTR (B2) | |||||||||
| VHCL SPEED SE | km/h or mph |
|
|||||||
| BATTERY VOLT | V |
|
|||||||
| ACCEL SEN 1 | V |
|
|
||||||
| ACCEL SEN 2 | |||||||||
| TP SEN 1-B1 | V |
|
|
||||||
| TP SEN 2-B1 | |||||||||
| FUEL T/TMP SE | °C or °F |
|
|||||||
| EVAP SYS PRES | V |
|
|||||||
| FUEL LEVEL SE | V |
|
|||||||
| START SIGNAL | ON/OFF |
|
|
||||||
| CLSD THL POS | ON/OFF |
|
|||||||
| AIR COND SIG | ON/OFF |
|
|||||||
| PW/ST SIGNAL | ON/OFF |
|
|||||||
| LOAD SIGNAL | ON/OFF |
ON: Rear window defogger switch is ON and/or lighting switch is in 2nd position. OFF: Both rear window defogger switch and lighting switch are OFF. |
|||||||
| IGNITION SW | ON/OFF |
|
|||||||
| HEATER FAN SW | ON/OFF |
|
|||||||
| BRAKE SW | ON/OFF |
|
|||||||
| INJ PULSE-B1 | msec |
|
|
||||||
| INJ PULSE-B2 | |||||||||
| IGN TIMING | BTDC |
|
|
||||||
| CAL/LD VALUE | % |
|
|||||||
| MASS AIRFLOW | g/s |
|
|||||||
| PURG VOL C/V | % |
|
|||||||
| EXH/V TIM B1 | °CA |
|
|||||||
| EXH/V TIM B2 | |||||||||
| INT/V SOL (B1) | % |
|
|||||||
| INT/V SOL (B2) | |||||||||
| AIR COND RLY | ON/OFF |
|
|||||||
| VENT CONT/V | ON/OFF |
ON: Closed OFF: Open |
|||||||
| THRTL RELAY | ON/OFF |
|
|||||||
| A/F S1 HTR (B1) | % |
|
|||||||
| A/F S1 HTR (B2) | |||||||||
| HO2S2 HTR (B1) | ON/OFF |
|
|||||||
| HO2S2 HTR (B2) | |||||||||
| ALT DUTY SIG | ON/OFF |
ON: Power generation voltage variable control is active. OFF: Power generation voltage variable control is inactive. |
|||||||
| I/P PULLY SPD | RPM |
|
|||||||
| VEHICLE SPEED | km/h or mph |
|
|||||||
| IDL A/V LEARN | YET/CMPLT |
YET: Idle air volume learning has not been performed yet. CMPLT: Idle air volume learning has already been performed successfully. |
|||||||
| TRVL AFTER MIL | km or mile |
|
|||||||
| SNOW MODE SW | ON/OFF |
|
|||||||
| ENG OIL TEMP | °C or °F |
|
|||||||
| VHCL SPEED SE | km/h or mph |
|
|||||||
| SET VHCL SPD | km/h or mph |
|
|||||||
| MAIN SW | ON/OFF |
|
|||||||
| CANCEL SW | ON/OFF |
|
|||||||
| RESUME/ACC SW | ON/OFF |
|
|||||||
| SET SW | ON/OFF |
|
|||||||
| BRAKE SW1 | ON/OFF |
|
|||||||
| BRAKE SW2 | ON/OFF |
|
|||||||
| DIST SW | ON/OFF |
|
|||||||
| VHCL SPD CUT | NON/CUT |
NON: Vehicle speed is maintained at the ASCD set speed. CUT: Vehicle speed decreased to excessively low compared with the ASCD set speed, and ASCD operation is cut off. |
|||||||
| LO SPEED CUT | NON/CUT |
NON: Vehicle speed is maintained at the ASCD set speed. CUT: Vehicle speed decreased to excessively low, and ASCD operation is cut off. |
|||||||
| AT OD MONITOR | ON/OFF |
|
|||||||
| AT OD CANCEL | ON/OFF |
|
|||||||
| CRUISE LAMP | ON/OFF |
|
|||||||
| SET LAMP | ON/OFF |
|
|||||||
| EXH V/T LEARN | YET/CMPLT |
YET: Exhaust Valve Timing Control Learning has not been performed yet. CMPLT: Exhaust Valve Timing Control Learning has already been performed successfully. |
|||||||
| FAN DUTY | % |
|
|||||||
| AC EVA TEMP | °C or °F |
|
|||||||
| AC EVA TARGET | °C or °F |
|
|||||||
| ALT DUTY | % |
|
|||||||
| BAT CUR SEN | mV |
|
|||||||
| A/F ADJ-B1 | - |
|
|||||||
| A/F ADJ-B2 | |||||||||
| TP SEN 1-B2 | V |
|
|
||||||
| TP SEN 2-B2 | |||||||||
| P/N POSI SW | ON/OFF |
|
|||||||
| INT/A TEMP SE | °C or °F |
|
|||||||
| AC PRESS SEN | V |
|
|||||||
| VTC DTY EX B1 | % |
|
|||||||
| VTC DTY EX B2 | |||||||||
| INT/V TIM (B1) | °CA |
|
|||||||
| INT/V TIM (B2) | |||||||||
| VVEL LEARN | YET/DONE |
YET: VVEL learning has not been performed yet. DONE: VVEL learning has already been performed successfully. |
|||||||
| VVEL SEN LEARN-B1 | V |
|
|||||||
| VVEL SEN LEARN-B2 | |||||||||
| VVEL POSITION SEN-B1 | V |
|
|||||||
| VVEL POSITION SEN-B2 | |||||||||
| VVEL TIM-B1 | deg |
|
|||||||
| VVEL TIM-B2 | |||||||||
| FPCM | HI/MID/LOW/OFF |
|
|||||||
| EVAP LEAK DIAG(1) | YET/CMPLT |
YET: EVAP leak diagnosis has not been performed yet. CMPLT: EVAP leak diagnosis has been performed successfully. |
|||||||
| EVAP DIAG READY(1) | ON/OFF |
ON: Diagnosis has been ready condition. OFF: Diagnosis has not been ready condition. |
|||||||
| THRTL STK CNT B1(2) | - | - | |||||||
| THRTL STK CNT B2(2) | |||||||||
| HO2 S2 DIAG1 (B1) (1) | INCMP/CMPLT |
INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete. |
|||||||
| HO2 S2 DIAG1 (B2) (1) | INCMP/CMPLT |
INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete. |
|||||||
| HO2 S2 DIAG2 (B1) (3) | INCMP/CMPLT |
INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete. |
|||||||
| HO2 S2 DIAG2 (B2) (3) | INCMP/CMPLT |
INCMP: Self-diagnosis is incomplete. CMPLT: Self-diagnosis is complete. |
|||||||
|
|||||||||
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
