Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Detailed Flow
- DIAGNOSIS WITH STARTING/CHARGING SYSTEM TESTER
Perform the starting system test with Starting/Charging System Tester (SST: J-44373). For details and operating instructions, refer to Starting/Charging System Tester (SST: J-44373) operating manual.
Test result
CRANKING VOLTAGE NORMAL: GO TO 2.
CRANKING VOLTAGE LOW: GO TO 5.
CHARGE BATTERY: Perform the slow battery charging procedure. (Initial rate of charge is 10A for 12 hours.) Perform battery test again. Refer to Starting/Charging System Tester (SST: J-44373) operating manual.
REPLACE BATTERY: Before replacing battery, clean the battery cable clamps and battery posts. Perform battery test again. Refer to Starting/Charging System Tester (SST: J-44373) operating manual. If second test result is "REPLACE BATTERY", then do so. Perform battery test again to confirm repair.
- CRANKING CHECK
Check that the starter motor operates correctly.
Does the engine crank normally?
YES: GO TO 3.
NO: GO TO 4.
- ENGINE START CHECK
Check that the engine starts.
Does the engine start?
YES: Starter motor is OK. INSPECTION END
NO: Starter motor is OK. Perform further diagnosis of engine mechanical or engine control system. Refer ENGINE MECHANICAL SYSTEM and ENGINE CONTROL SYSTEM (VQ35HR) . Once resolved, perform battery test again.
- STARTER MOTOR ACTIVATION
Check that the starter motor operates.
Does the starter motor turn?
YES: Check ring gear and starter motor drive pinion. Once resolved, perform battery test again.
NO: GO TO 7.
- COMPARISON BETWEEN ENGINE COOLANT AND CRANKING VOLTAGE
Compare the engine coolant temperature and the cranking voltage with the specifications.
MINIMUM SPECIFICATION OF CRANKING VOLTAGE REFERENCING COOLANT TEMPERATURE CHARTEngine coolant temperature [°C (°F)] Voltage [V] -30 to -20 (-22 to -4) 8.6 -19 to -10 (-2 to 14) 9.1 -9 to 0 (16 to 32) 9.5 More than 1 (More than 34) 9.9 Is the voltage less than the specified value?
YES: GO TO 7.
NO: GO TO 6.
- STARTER OPERATION
Check the starter operation status.
Does the starter motor turn smoothly?
YES: Starter motor is OK. INSPECTION END
NO: GO TO 7.
- "B" TERMINAL CIRCUIT INSPECTION
Check "B" terminal circuit. Refer to "DIAGNOSIS PROCEDURE ".
Is "B" terminal circuit normal?
YES: GO TO 8.
NO: Repair as needed.
- "S" CONNECTOR CIRCUIT INSPECTION
Check "S" connector circuit. Refer to "DIAGNOSIS PROCEDURE ".
Is "S" connector circuit normal?
YES: GO TO 9.
NO: Repair as needed.
- ENGINE ROTATION STATUS
Check that the engine can be rotated by hand.
Does the engine turn freely by hand?
YES: Replace starter motor.
NO: Perform further diagnosis of engine mechanical or powertrain mechanism. Once resolved, perform battery test again. Refer to Starting/Charging System Tester (SST: J-44373) operating manual.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
