2011 Infiniti M37 BaseFACTORY OEM SERVICE PROCEDURE

POWER DISTRIBUTION SYSTEM : System Description

WARNING: This page is about a different car, the 2011 Infiniti QX56. However, it is still accessible from the selected car via links, so may be relevant.

SYSTEM DESCRIPTION

  • PDS (POWER DISTRIBUTION SYSTEM) is the system that BCM controls with the operation of the pushbutton ignition switch and performs the power distribution to each power circuit. This system is used instead of the mechanical power supply changing mechanism with the operation of the conventional key cylinder.
  • The push-button ignition switch can be operated when Intelligent Key is in the following condition. Refer to Engine Start Function for details.
    • Intelligent Key is in the detection area of the inside key antenna.
    • Intelligent Key backside is contacted to push-button ignition switch.
  • The push-button ignition switch operation is input to BCM as a signal. BCM changes the power supply position according to the status and operates the following relays to supply power to each power circuit.
    • Ignition relay (inside IPDM E/R)
    • Ignition relay-1
    • ACC relay
    • Blower relay
      NOTE: The engine switch operation changes due to the conditions of brake pedal, selector lever and vehicle speed.
  • The power supply position can be confirmed with the lighting of the indicators near the push-button ignition switch.

BATTERY SAVER SYSTEM

When all the following conditions are met for 60 minutes, the battery saver system will cut off the power supply to prevent battery discharge.

  • The ignition switch is in the ACC position
  • All doors are closed
  • Selector lever is in the P position

Reset Condition of Battery Saver System

In order to prevent the battery from discharging, the battery saver system will cut off the power supply when all doors are closed, the selector lever is on P position and the ignition switch is left on ACC position for 1 hour. If any of the following conditions are met the battery saver system is released and the steering will change automatically to lock position from OFF position.

  • Opening any door
  • Operating with door request switch on door lock
  • Operating with Intelligent Key on door lock

Press push-button ignition switch and ignition switch will change to ACC position from OFF position.

STEERING LOCK OPERATION

Steering is locked by steering lock unit when ignition switch is in the OFF position, selector lever is in the P position and any of the following conditions are met.

  • Opening door
  • Closing door
  • Door is locked with door request switch
  • Door is locked with Intelligent Key

POWER SUPPLY POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION

The power supply position changing operation can be performed with the following operations.

NOTE:
  • When an Intelligent Key is within the detection area of inside key antenna and when Intelligent Key backside is contacted to push-button ignition switch, it is equivalent to the operations below.
  • When starting the engine, the BCM monitors under the engine start conditions,
    • Brake pedal operating condition
    • Selector lever position
    • Vehicle speed

Vehicle speed: less than 4 km/h (2.5 MPH)

POWER SUPPLY POSITION

Power supply position Engine start/stop condition Push-button ignition switch operation frequency
Selector lever position Brake pedal operation condition
LOCK β†’ ACC - Not depressed 1
LOCK β†’ ACC β†’ ON - Not depressed 2
LOCK β†’ ACC β†’ ON β†’ OFF - Not depressed 3
LOCK β†’ START
ACC β†’ START
ON β†’ START
P or N position Depressed 1
Engine is running β†’ OFF - - 1

Vehicle speed: 4 km/h (2.5 MPH) or more

POWER SUPPLY POSITION

Power supply position Engine start/stop condition Push-button ignition switch operation frequency
Selector lever position Brake pedal operation condition
Engine is running β†’ ACC - - Emergency stop operation
Engine stall return operation while driving N position Not depressed 1

Emergency stop operation

  • Press and hold the push-button ignition switch for 2 seconds or more.
  • Press the push-button ignition switch 3 times or more within 1.5 seconds.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.