Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Infiniti M35 BaseFACTORY OEM SERVICE PROCEDURE
Specifications with CONSULT-II
AWD CONTROL UNIT INPUT/OUTPUT SIGNAL REFERENCE VALUES
| Monitor item [Unit] | Content | Condition | Display value | ||||
|---|---|---|---|---|---|---|---|
| FR RH SENSOR [km/h] or [mph] | Wheel speed (Front wheel right) | Vehicle stopped | 0.00 km/h (0.00 mph) | ||||
| Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
|
Approximately equal to the indication on speedometer (Inside of ±10%) | ||||||
| FR LH SENSOR [km/h] or [mph] | Wheel speed (Front wheel left) | Vehicle stopped | 0.00 km/h (0.00 mph) | ||||
| Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
|
Approximately equal to the indication on speedometer (Inside of ±10%) | ||||||
| RR RH SENSOR [km/h] or [mph] | Wheel speed (Rear wheel right) | Vehicle stopped | 0.00 km/h (0.00 mph) | ||||
| Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
|
Approximately equal to the indication on speedometer (Inside of ±10%) | ||||||
| RR LH SENSOR [km/h] or [mph] | Wheel speed (Rear wheel left) | Vehicle stopped | 0.00 km/h (0.00 mph) | ||||
| Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
|
Approximately equal to the indication on speedometer (Inside of ±10%) | ||||||
| BATTERY VOLT [V] | Power supply voltage for AWD control unit | Ignition switch: ON | Battery voltage | ||||
| THRTL POS SEN [%] | Throttle opening condition | When depressing accelerator pedal (Value rises gradually in response to throttle position.) | 0 - 100% | ||||
| ETS SOLENOID [A] | Monitored value of current at AWD solenoid | Engine running
|
Approx. 0.000A | ||||
Engine running
|
Approx. 0.000 - 0.500A(1) | ||||||
| STOP LAMP SW [ON/OFF] | Condition of brake pedal operation | Brake pedal: Depressed | ON | ||||
| Brake pedal: Released | OFF | ||||||
| ENG SPEED SIG [RUN/STOP] | Condition of engine running | Engine stopped (Engine speed: Less than 400 rpm) |
STOP | ||||
| Engine running (Engine speed: 400 rpm or more) |
RUN | ||||||
| ETS ACTUATOR [ON/OFF] | Operating condition of AWD actuator relay (integrated in AWD control unit) | Engine stopped (Ignition switch: ON) | OFF | ||||
| Engine running | ON | ||||||
| 4WD WARN LAMP [ON/OFF] | AWD warning lamp condition | AWD warning lamp: ON | ON | ||||
| AWD warning lamp: OFF | OFF | ||||||
| 4WD MODE SW(2) [AUTO] | Input condition from mode switch | Always | AUTO | ||||
| 4WD MODE MON [AUTO] | Control status of AWD | Engine running | AUTO | ||||
| DIS-TIRE MONI [mm] | Improper size tire installed condition | Vehicle running with normal size tire installed | 0-4 mm | ||||
| Vehicle running with improper size tire installed (Front/rear tire size difference, wear condition) | 4-8 mm, 8-mm | ||||||
| P BRAKE SW [ON/OFF] | Condition of parking brake | Parking brake operated | ON | ||||
| Parking brake not operated | OFF | ||||||
|
|||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.