Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- INSPECTION STARTÂ
Start engine.
Is engine running?Â
Yes or No
- Yes: GO TO Â 14.
- No: GO TO 2.
- CHECK ECM POWER SUPPLY CIRCUIT-IÂ
- Turn ignition switch OFF and then ON.
- Check voltage between ECM terminal 109 and ground with CONSULT-II or tester.
- Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO 4.
- NG: GO TO 3.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E32, F32
- Fuse block (J/B) No. 1 connector M1
- Fuse block (J/B) No. 2 connectors M143, E215
- 15A fuse
- Harness for open or short between ECM and fuse
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK GROUND CONNECTIONSÂ
- Turn ignition switch OFF.
- Loosen and retighten three ground screws on the body. Refer to "GROUND INSPECTIONÂ ".
OK or NGÂ
- OK: GO TO 5.
- NG: Repair or replace ground connections.
- CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-IÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminals 1, 115, 116 and ground. Refer to WIRING DIAGRAM
.
- Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO Â 9.
- NG: GO TO 6.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors F32, E32
- Harness for open or short between ECM and ground
- Repair open circuit or short to power in harness or connectors.
- CHECK ECM POWER SUPPLY CIRCUIT-IIÂ
- Disconnect ECM relay.
- Check voltage between ECM relay terminals 2, 5 and ground with CONSULT-II or tester.
- Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 11.
- NG: GO TO 8.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- 10A fuse
- 20A fuse
- Fuse block (J/B) No. 2 connector E215
- Fuse, fusible link and relay block (J/B) connector E3
- Harness for open or short between ECM relay and battery
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Check harness continuity between ECM terminal 111 and ECM relay terminal 1. Refer to WIRING DIAGRAM
.
- Continuity should exist.Â
- Also check harness for short to ground and short to power.Â
OK or NGÂ
- OK: GO TO Â 13.
- NG: GO TO 10.
- Check harness continuity between ECM terminal 111 and ECM relay terminal 1. Refer to WIRING DIAGRAM
.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M135, F105
- Fuse block (J/B) No. 2 connector M143
- Harness for open or short between ECM relay and ECM
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ECM RELAYÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
- OK: GO to "Â IGNITION SIGNALÂ "Â .
- NG: Replace ECM relay.
- CHECK ECM POWER SUPPLY CIRCUIT-IIIÂ
- Turn ignition switch ON and then OFF.
- Check voltage between ECM terminals 119, 120 and ground with CONSULT-II or tester.
- Voltage: After turning ignition switch OFF, battery voltage will exist for a few seconds, then drop approximately 0V.Â
OK or NGÂ
- OK: GO TO 18.
- NG (Battery voltage does not exist.): GO TO 13.
- NG (Battery voltage exists for more than a few seconds.): GO TO Â 12.
- CHECK ECM POWER SUPPLY CIRCUIT-IVÂ
- Disconnect ECM relay.
- Check voltage between ECM relay terminal 7 and ground with CONSULT-II or tester.
- Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 17.
- NG: GO TO 14.
- DETECT MALFUNCTIONING PARTÂ
Check harness for open or short between ECM relay and 10A fuse
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ECM POWER SUPPLY CIRCUIT-VÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminals 119, 120 and ECM relay terminal 6. Refer to WIRING DIAGRAM
.
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 19.
- NG: GO TO 16.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M135, F105
- Fuse block (J/B) No. 2 connector M143
- Harness for open or short between ECM and ECM relay
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ECM RELAYÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
- OK: GO TO 18.
- NG: Replace ECM relay.
- CHECK GROUND CONNECTIONSÂ
- Turn ignition switch OFF.
- Loosen and retighten three ground screws on the body. Refer to "GROUND INSPECTIONÂ ".
OK or NGÂ
- OK: GO TO 19.
- NG: Repair or replace ground connections.
- CHECK ECM GROUND CIRCUIT FOR OPEN AND SHORT-IIÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminals 1, 115, 116 and ground. Refer to WIRING DIAGRAM
.
- Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO Â 23.
- NG: GO TO 20.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors F32, E32
- Harness for open or short between ECM and ground
- Repair open circuit or short to power in harness or connectors.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ ".
- INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
