Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK OVERALL FUNCTION-IÂ
- Turn ignition switch ON.
- Select "SNOW MODE SW" in "DATA MONITOR" mode with CONSULT-II.
- Check "SNOW MODE SW" indication under the following conditions.CONDITION CHECK
CONDITION INDICATION Snow mode switch: ON ON Snow mode switch: OFF OFF
OK or NGÂ
- OK: GO TO 2.
- NG: GO TO Â 3.
- CHECK OVERALL FUNCTION-IIÂ
- Turn ignition switch ON.
- Check snow indicator in the snow mode switch under the following conditions.CONDITION CHECK
CONDITION INDICATOR Snow mode switch: ON Illuminated Snow mode switch: OFF Not illuminated
OK or NGÂ
- OK: INSPECTION ENDÂ
- NG: GO TO Â 10.
- CHECK DTCÂ
Check that DTC U1000 or U1001 is not displayed.
OK or NGÂ
- OK: GO TO 4.
- NG: Perform trouble diagnoses for DTC U1000, U1001. Refer to "DTC U1000, U1001 CAN COMMUNICATION LINEÂ ".
- CHECK SNOW MODE SWITCH CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect combination meter harness connector.
- Turn ignition switch ON.
- Check voltage between combination meter terminal 16 and ground under the following conditions with CONSULT-II or tester.CONDITION CHECK
CONDITION VOLTAGE Snow mode switch: ON Battery voltage (11 - 14V) Snow mode switch: OFF 0V
OK or NGÂ
- OK: GO TO 5.
- NG: GO TO Â 6.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ ".
OK or NGÂ
- OK: Replace combination meter.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK SNOW MODE SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect snow mode switch harness connector.
- Turn ignition switch ON.
- Check voltage between snow mode switch terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 8.
- NG: GO TO 7.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E105, M13
- IPDM E/R harness connector E8
- 10A fuse
- Harness for open or short between snow mode switch and fuse.
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK SNOW MODE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Check harness continuity between snow mode switch terminal 4 and combination meter terminal 16. Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO 9.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK SNOW MODE SWITCHÂ
Refer to "Component Inspection ".
OK or NGÂ
- OK: GO TO Â 13.
- NG: Replace snow mode switch.
- CHECK GROUND CONNECTIONSÂ
- Turn ignition switch OFF.
- Loosen and retighten two ground screws on the body. Refer to "Ground Inspection ".
OK or NGÂ
- OK: GO TO Â 12.
- NG: Repair or replace ground connections.
- CHECK SNOW INDICATOR GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect snow mode switch harness connector.
- Check harness continuity between snow mode switch terminal 2 and ground. Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO 12.
- NG: Repair open circuit or short to power in harness or connectors.
- CHECK SNOW INDICATORÂ
Check continuity between snow mode switch terminals 2 and 4 under the following conditions.
CONDITION CHECKCondition Continuity 1 Should exist. 2 Should not exist. Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NGÂ
- OK: GO TO 13.
- NG: Replace snow mode switch.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ ".
- : INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
