2004 Infiniti I35FACTORY OEM SERVICE PROCEDURE

Basic Inspection

Precaution:Ā 

Perform Basic Inspection without electrical or mechanical loads applied;Ā 

  • Headlamp switch is OFF,
  • Air conditioner switch is OFF,
  • Rear window defogger switch is OFF,
  • Steering wheel is in the straight-ahead position, etc.
  1. INSPECTION STARTĀ 
    1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
    2. Open engine hood and check the following:
      • Harness connectors for improper connections
      • Vacuum hoses for splits, kinks and improper connection
      • Wiring for improper connections, pinches and cuts
      • Air cleaner clogging
      • Hoses and ducts for leaks
      1. : Go To 2.
  2. REPAIR OR REPLACEĀ 

    Repair or replace components as necessary according to corresponding Diagnostic Procedure.

    1. : Go To 3.
  3. CHECK TARGET IDLE SPEEDĀ 

    With CONSULT-II

    1. Run engine at about 2,000 rpm for about 2 minutes under no load.
    2. Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about minute.
    3. Read idle speed in DATA MONITOR mode with CONSULT-II. See Figure .

      675+/-50 rpm (in P or N position)Ā 

    Without CONSULT-II

    1. Run engine at about 2,000 rpm for about 2 minutes under no load
    2. Rev engine (2,000 to 3,000 rpm) two or three times under no load, then run engine at idle speed for about one minute.
    3. check idle speed

      675+/-rpm (in P or N position)Ā 

    OK or NGĀ 

    1. OK: GO TO Ā 10 .
    2. NG: GO TO 4.
  4. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNINGĀ 
    1. Stop engine.
    2. Perform ACCELERATOR PEDAL RELEASED POSITION LEARNINGĀ  .
    1. GO TO 5.
  5. PERFORM THROTTLE VALVE CLOSED POSITION LEARNINGĀ 

    Perform THROTTLE VALVE CLOSED POSITION LEARNINGĀ  .

    1. GO TO 6.
  6. PERFORM IDLE AIR VOLUME LEARNINGĀ 

    Refer to IDLE AIR VOLUME LEARNINGĀ  .

    Is Idle Air Volume Learning carried out successfully?Ā 

    Yes or NoĀ 

    1. Yes: GO TO 7.
    2. No:
      1. Follow the instruction of Idle Air Volume Learning.
      2. GO TO Ā 4 .
  7. CHECK TARGET IDLE SPEED AGAINĀ 

    With CONSULT-II

    1. Start engine and warm it up to normal operating temperature.
    2. Read idle speed in DATA MONITOR mode with CONSULT-II.

      675+/-50 rpm (in P or N position)Ā 

    Without CONSULT-II

    1. Start engine and warm it up to normal operating temperature.
    2. Check idle speed.

      675+/-50 rpm (in P or N position)Ā 

      OK or NGĀ 

    1. OK GO TO Ā 10 .
    2. NG GO TO 8.
  8. DETECT MALFUNCTIONING PARTĀ 

    Check the following.

    1. OK GO TO 9.
    2. NG
      1. Repair or replace.
      2. GO TO Ā 4 .
  9. CHECK ECM FUNCTIONĀ 
    1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of a malfunction, but this is the rarely the case.)
    2. Perform initialization of IVIS (NATS) system and registration of IVIS (NATS) ignition key IDs. Refer to IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM - NATS)Ā  .
    1. GO TO Ā 4 .
  10. CHECK IGNITION TIMINGĀ 
    1. Run engine at idle.
    2. Check ignition timing with a timing light. See Figure .

      15°+/-5° BTDC (in P or N position) 

      OK or NGĀ 

    1. OK INSPECTION ENDĀ 
    2. NG GO TO 11.
  11. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNINGĀ 
    1. Stop engine.
    2. Perform ACCELERATOR PEDAL RELEASED POSITION LEARNINGĀ  .
      1. GO TO 12.
  12. PERFORM THROTTLE VALVE CLOSED POSITION LEARNINGĀ 

    Perform THROTTLE VALVE CLOSED POSITION LEARNINGĀ  .

    1. GO TO 13.
  13. PERFORM IDLE AIR VOLUME LEARNINGĀ 

    Refer to IDLE AIR VOLUME LEARNINGĀ  .

    Is Idle Air Volume Learning carried out successfully?Ā 

    Yes or NoĀ 

    1. Yes GO TO 14.
    2. No
      1. Follow the instruction of Idle Air Volume Learning.
      2. GO TO Ā 4 .
  14. CHECK TARGET IDLE SPEED AGAINĀ 

    With CONSULT-IIĀ 

    1. Start engine and warn it up to normal operating temperature.
    2. Read idle speed in DATA MONITOR mode with CONSULT-II.

      675+/-50 rpm (in P or N position)Ā 

    Without CONSULT-IIĀ 

    1. Start engine and warm it up to normal operating temperature.
    2. Check idle speed.

      675+/-50 rpm (in P or N position)Ā 

      OK or NGĀ 

    1. OK GO TO 15.
    2. NG GO TO Ā 17 .
  15. CHECK IGNITION TIMING AGAINĀ 
    1. Run engine at idle.
    2. Check ignition timing with a timing light. See Figure .

      15°+/-5° BTDC (in P or N position) 

      OK or NGĀ 

    1. OK INSPECTION ENDĀ 
    2. NG GO TO 16.
  16. CHECK TIMING CHAIN INSTALLATIONĀ 

    Check timing chain installation. Refer to TIMING CHAIN .

    OK or NGĀ 

    1. OK GO TO 17.
    2. NG
      1. Repair the timing chain installation.
      2. GO TO Ā 4 .
  17. DETECT MALFUNCTIONING PARTĀ 

    Check the following.

    1. OK GO TO 18.
    2. NG
      1. Repair or replace.
      2. GO TO Ā 4 .
  18. CHECK ECM FUNCTIONĀ 
    1. Substitute another known-good ECM to check ECM function. (ECM may be the cause of a malfunction, but this is the rarely the case.)
    2. Perform initialization of IVIS (NATS) system and registration of IVIS (NATS) ignition key IDs. Refer to IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM - NATS)Ā  .
    1. GO TO Ā 4 .
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.