Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- RETIGHTEN GROUND SCREWSÂ
- Turn ignition switch OFF.
- Loosen and retighten engine ground screws. See Figure .
- : GO TO 2
- CHECK THROTTLE CONTROL MOTOR GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 107 and engine ground.
Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO 3.
- NG: Repair open circuit or short to power in harness or connectors.
- CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-IÂ
- Reconnect harness connector disconnected.
- Check voltage between ECM terminal 102 and ground under the following conditions with CONSULT-II or tester.
OK or NGÂ
- OK: GO TO Â 12 .
- NG: GO TO 4.
- CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect throttle control motor relay.
- Check voltage between throttle control motor relay terminals 2, 5 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 6 .
- NG: GO TO 5.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- 15A fuse
- Harness for open and short between throttle control motor relay and fuse
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-IIÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 102 and throttle control motor relay terminal 3.
Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 8 .
- NG: GO TO 7.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connector E15, F18
- Harness for open and short between throttle control motor relay and ECM
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK THROTTLE CONTROL MOTOR RELAY OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Check harness continuity between ECM terminal 26 and throttle control motor relay terminal 1.
Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 10 .
- NG: GO TO 9.
- Check harness continuity between ECM terminal 26 and throttle control motor relay terminal 1.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connector E81, M15
- Harness connectors M223, F53
- Harness for open and short between throttle control motor relay and ECM
- : Repair open circuit to short to ground or short to power in harness or connectors.
- CHECK THROTTLE CONTROL MOTOR RELAYÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 11.
- NG: Replace throttle control motor relay.
- CHECK INTERMITTENT INCIDENTÂ
Perform TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
- : INSPECTION ENDÂ
- CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORTÂ
- Turn ignition switch OFF.
- Disconnect electric throttle control actuator harness connector. See Figure .
- Disconnect ECM harness connector.
- Check harness continuity between the following terminals.
Refer to Wiring Diagram.
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO 13.
- NG: Repair or replace.
- CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLYÂ
- Remove the intake air duct.
- Check if foreign matter is caught between the throttle valve and the housing. See Figure .
OK or NGÂ
- OK: GO TO 14.
- NG: Remove the foreign matter and clean the electric throttle control actuator inside.
- CHECK THROTTLE CONTROL MOTORÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 15.
- NG: GO TO Â 16 .
- CHECK INTERMITTENT INCIDENTÂ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
OK or NGÂ
- OK: GO TO 16.
- NG: Repair or replace harness or connectors.
- REPLACE ELECTRIC THROTTLE CONTROL ACTUATORÂ
- Replace the electric throttle control actuator.
- Perform THROTTLE VALVE CLOSED POSITION LEARNINGÂ .
- Perform IDLE AIR VOLUME LEARNINGÂ .
- : INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
