Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- RETIGHTEN GROUND SCREWSÂ
- Turn ignition switch OFF.
- Loosen and retighten engine ground screws. See Figure .
- : GO TO 2.
- CHECK CONNECTORÂ
- Disconnect EVAP control system pressure sensor harness connector.
- Check sensor harness connector for water.
Water should not exist.Â
OK or NGÂ
- OK: GO TO 3.
- NG: Repair or replace harness connector.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUITÂ
- Turn ignition switch ON.
- Check voltage between EVAP control system pressure sensor terminal 1 and ground with CONSULT-II or tester.
Courtesy of NISSAN MOTOR CO., U.S.A.
Voltage: Approximately 5VÂ
OK or NGÂ
- OK: GO TO Â 5 .
- NG: GO TO 4.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors B2, M2
- Harness connectors M81, F49
- Harness for open for short between EVAP control system pressure sensor and ECM
- : Repair harness or connectors.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Check harness continuity between EVAP control system pressure sensor terminal 3 and engine ground.
Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO Â 7 .
- NG: GO TO 6.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors B2, M2
- Harness connectors M81, F49
- Joint connector-20
- Harness for open between EVAP control system pressure sensor and ECM
- : Repair open circuit or short to power in harness or connectors.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 60 and EVAP control system pressure sensor terminal 2.
Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 9 .
- NG: GO TO 8.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors B2, M2
- Harness connectors M81, F49
- Harness for open or short between ECM and EVAP control system pressure sensor
- : Repair open circuit or short to ground or short to in harness or connectors.
- CHECK RUBBER TUBE FOR CLOGGINGÂ
- Disconnect rubber tube connected to EVAP canister vent control valve.
- Check the rubber tube for clogging.
OK or NGÂ
- OK: GO TO 10.
- NG: Clean the rubber tube suing an air blower.
- CHECK EVAP CANISTER VENT CONTROL VALVE-IÂ
- Remove EVAP canister vent control valve from EVAP canister.
- Check portion B of EVAP canister vent control valve for being rusted.
- OK: GO TO 11.
- NG: Replace EVAP canister vent control valve.
- CHECK EVAP CANISTER VENT CONTROL VALVEÂ
With CONSULT-IIÂ
- Perform VENT CONTROL/V in ACTIVE TEST mode.
- Check air passage continuity and operation delay time under the following conditions. See Figure
.
Without CONSULT-IIÂ
Check air passage continuity and operation delay time under the following conditions. See Figure .
Make sure new O-ring is installed properly.Â
OK or NGÂ
- OK: GO TO Â 13 .
- NG: GO TO 12.
- CHECK EVAP CANISTER VENT CONTROL VALVE-IIIÂ
- Clean the air passage (portion A to B) of EVAP canister vent control valve using an air blower.
- Perform Test No. 14 again.
OK or NGÂ
- OK: GO TO 13.
- NG: Replace EVAP canister vent control valve.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSORÂ
- Remove EVAP control system pressure sensor with its harness connector connected.CAUTION: Never apply force to the air hole protector of the sensor if equipped. See Figure .
- Remove hose from EVAP control system pressure sensor.
- Turn ignition switch ON.
- Use pump to apply vacuum and pressure to EVAP control system pressure sensor as shown in Figure
.CAUTION:
- Always calibrate the vacuum pump gauge when using it.
- Do not apply below -20 kPa (-150 mmHg, -5.91 inHg) or over 20 kPa (150 mmHg, 5.91 inHg) of pressure.
- Check input voltage between ECM terminal 60 and ground. See Figure
and Figure
.CAUTION: Discard and EVAP control system pressure sensor which has been dropped from a height of more than 0.5m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
OK or NGÂ
- OK: GO TO 14.
- NG: Replace EVAP control system pressure sensor.
- Remove EVAP control system pressure sensor with its harness connector connected.
- CHECK RUBBER TUBEÂ
Check obstructed rubber tube connected to EVAP canister vent control valve.
OK or NGÂ
- OK: GO TO 15.
- NG: Clean rubber tube using an air blower, repair or replace rubber tube.
- CHECK WATER SEPARATORÂ
- Check visually for insect nests in the water separator air inlet.
- Check visually for cracks or flaws in the appearance.
- Check visually for cracks or flaws in the house.
- Check that A and C are not clogged by blowing air into B with A, and then C plugged. See Figure .
- In case of NG in items 2 - 4, replace the parts.NOTE: Do not disassemble water separator.
OK or NGÂ
- OK: GO TO 16.
- NG: Replace water separator.
- CHECK IF EVAP CANISTER SATURATED WITH WATERÂ
- Remove EVAP canister with EVAP canister vent control valve attached.
- Check if water will drain from the EVAP canister. See Figure .
Yes or NoÂ
- Yes: GO TO 17.
- No: GO TO Â 19 .
- CHECK EVAP CANISTERÂ
Weigh the EVAP canister with the EVAP canister vent control valve attached.
The weight should be less than 1.8 kg (4.0 Ib).Â
OK or NGÂ
- OK: GO TO Â 19 .
- NG: GO TO 18.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- EVAP canister for damage
- EVAP hose between EVAP canister and water separator for clogging or poor connection
- : Repair hose or replace EVAP canister.
- CHECK INTERMITTENT INCIDENTÂ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
- INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
