Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- INSPECTION STARTÂ
Which malfunction (P0102 or P0103) is duplicated?
P0102 or P0103Â
- P0103: GO TO Â 3 .
- P0102: GO TO 2.
- CHECK INTAKE SYSTEMÂ
Check the following for connection.
- Air duct
- Vacuum hoses
- Intake air passage between air duct to intake manifold collector
OK or NGÂ
- OK: GO TO 3.
- NG: Reconnect the parts.
- RETIGHTEN GROUND SCREWSÂ
- Turn ignition switch OFF.
- Loosen and retighten engine ground screws. See Figure .
- : GO TO 4.
- CHECK MAF SENSOR POWER SUPPLY CIRCUITÂ
- Disconnect mass air flow (MAF) sensor harness connector.
- Turn ignition switch ON.
- Check voltage between MAF sensor terminals 2, 4 and ground with CONSULT-II or tester.
OK or NGÂ
- OK: GO TO Â 6 .
- NG: GO TO 5.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E15, F18
- Harness for open or short between ECM relay and mass air flow sensor
- Harness for open or short between mass air flow sensor and ECM
- : Repair harness or connectors.
- CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between MAF sensor terminal 3 and ECM terminal 80. Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to power.
OK or NGÂ
- OK: GO TO 7.
- NG: Repair open circuit or short to power in harness or connectors.
- CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Check harness continuity between MAF sensor terminal 1 and ECM terminal 62. Refer to Wiring Diagram.
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO 8.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- Check harness continuity between MAF sensor terminal 1 and ECM terminal 62. Refer to Wiring Diagram.
- CHECK MASS AIR FLOW SENSORÂ
- Reconnect harness connectors disconnected.
- Start engine and warm it up to normal operating temperature.
- Check voltage between ECM terminal 62 (Mass air flow sensor signal) and ground.
- If the voltage is out of specification, disconnect MAF sensor harness connector and connect it again. Then repeat above check.
OK or NGÂ
- OK: GO TO 9.
- NG: Replace mass air flow sensor.
- CHECK INTERMITTENT INCIDENTÂ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
- : INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
