2004 Infiniti FX35 RWDFACTORY OEM SERVICE PROCEDURE

Diagnostic Procedure

  1. Check Fuel Filler Cap DesignĀ 
    1. Turn ignition switch OFF.
    2. Check for genuine NISSAN fuel filler cap design.

    OK or NG

    1. OK: Go to 2.
    2. NG: Replace with genuine NISSAN fuel filler cap.

  2. Check Fuel Filler Cap InstallationĀ 

    Check that the cap is tightened properly by rotating the cap clockwise.

    OK or NG

    1. OK: Go to 3.
    2. NG:
      1. Open fuel filler cap, then clean cap and fuel filler neck threads using air blower.
      2. Retighten until ratcheting sound is heard.

  3. Check Fuel Filler Cap FunctionĀ 

    Check for air releasing sound while opening the fuel filler cap.

    OK or NG

    1. OK: Go to Ā 5.
    2. NG: Go to 4.

  4. Check Fuel Tank Vacuum Relief ValveĀ 

    Refer to FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FILLER CAP)Ā .

    OK or NG

    1. OK: Go to 5.
    2. NG: Replace fuel filler cap with a genuine one.

  5. Check EVAP Purge LineĀ 

    Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks, improper connection or disconnection.

    Refer to EVAPORATIVE EMISSION LINE DRAWINGĀ .

    OK or NG

    1. OK: Go to 6.
    2. NG: Repair or reconnect the hose.

  6. Clean EVAP Purge LineĀ 

    Clean EVAP purge line (pipe and rubber tube) using air blower.

    1. Go to 7.
  7. Check EVAP Canister Vent Control ValveĀ 

    Check the following.

    OK or NG

    1. OK: Go to 8.
    2. NG: Repair or replace EVAP canister vent control valve and "O" ring.

  8. NOTE: Improper installation of the EVAP service port adapter to the EVAP service port may cause leaking.
  9. Install The Pressure PumpĀ 

    To locate the EVAP leak, install EVAP service port adapter and pressure pump to EVAP service port securely. See Figure and Figure.

    Models with CONSULT-II: Go to 9.

    Models without CONSULT-II: Go to Ā 10.

  10. Check For EVAP LeakĀ 

    With CONSULT-IIĀ 

    1. Turn ignition switch ON.
    2. Select EVAP SYSTEM CLOSE of WORK SUPPORT mode with CONSULT-II.
    3. NOTE:
      • Never use compressed air or a high pressure pumpĀ  .
      • Do not exceed 4.12 kPa (0.042 kg/cm2Ā  , 0.6 psi) of pressure in the systemĀ  .
    4. Touch START and apply pressure into the EVAP line until the pressure indicator reaches the middle of the bar graph. See Figure.
    5. Using EVAP leak detector, locate the EVAP leak. For the leak detector, refer to the instruction manual for more details.

      Refer to EVAPORATIVE EMISSION LINE DRAWINGĀ .

    OK or NG

    1. OK: Go to 11.
    2. NG: Repair or replace.
      Fig 1: EVAP Leak Detector
      G00727450Courtesy of NISSAN MOTOR CO., U.S.A.
  11. Check For EVAP LeakĀ 

    Without CONSULT-IIĀ 

    1. Turn ignition switch OFF.
    2. Apply 12 volts DC to EVAP canister vent control valve. The valve will close. (Continue to apply 12 volts until the end of test.)
      Fig 2: Under Vehicle View Of EVAP Control System
      G00727451Courtesy of NISSAN MOTOR CO., U.S.A.
    3. Pressurize the EVAP line using pressure pump with 1.3 to 2.7 kPa (10 to 20 mmHg, 0.39 to 0.79 inHg), then remove pump and EVAP service port adapter.
      NOTE:
      • Never use compressed air or a high pressure pumpĀ  .
      • Do not exceed 4.12 kPa (0.042 kg/cm2Ā  , 0.6 psi) of pressure in the systemĀ  .
    4. Using EVAP leak detector, locate the EVAP leak. For the leak detector, refer to the instruction manual for more details. Refer to EVAPORATIVE EMISSION LINE DRAWINGĀ .

    OK or NG

    1. OK: Go to Ā 12.
    2. NG: Repair or replace.
      Fig 3: EVAP Leak Detector
      G00727452Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Check EVAP Canister Purge Volume Control Solenoid Valve OperationĀ 

    With CONSULT-IIĀ 

    1. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
    2. Start engine.
    3. Perform PURG VOL CONT/V in ACTIVE TEST mode. See Figure.
    4. Touch Qu on CONSULT-II screen to increase PURG VOL CONT/V opening to 100%.
    5. Check vacuum hose for vacuum when revving engine up to 2,000 RPM.

    OK or NG

    1. OK: Go to Ā 14.
    2. NG: Go to Ā 13.

  13. Check EVAP Canister Purge Volume Control Solenoid Valve OperationĀ 

    Without CONSULT-IIĀ 

    1. Start engine and warm it up to normal operating temperature.
    2. Stop engine.
    3. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
    4. Start engine and let it idle for at least 80 seconds.
    5. Check vacuum hose for vacuum when revving engine up to 2,000 RPM.

    Vacuum should existĀ  .

    OK or NG

    1. OK: Go to Ā 15.
    2. NG: Go to 13.

  14. Check Vacuum HoseĀ 

    Check vacuum hoses for clogging or disconnection. Refer to Vacuum Hose DrawingĀ .

    OK or NG

    OK (With CONSULT-II): Go to 14.

    OK (Without CONSULT-II): Go to Ā 15.

    NG: Repair or reconnect the hose.

  15. Check EVAP Canister Purge Volume Control Solenoid ValveĀ 

    With CONSULT-IIĀ 

    1. Start engine.
    2. Perform PURG VOL CONT/V in ACTIVE TEST mode with CONSULT-II. Check that engine speed varies according to the valve opening. See Figure.

    OK or NG

    1. OK: Go to Ā 16.
    2. NG: Go to 15.

  16. Check EVAP Canister Purge Volume Control Solenoid ValveĀ 

    Refer to COMPONENT INSPECTIONĀ .

    OK or NG

    1. OK: Go to 16.
    2. NG: Replace EVAP canister purge volume control solenoid valve.

  17. Check Fuel Tank Temperature SensorĀ 

    Refer to COMPONENT INSPECTIONĀ .

    OK or NG

    1. OK: Go to 17.
    2. NG: Replace fuel level sensor unit.

  18. Check EVAP Control System Pressure SensorĀ 

    Refer to COMPONENT INSPECTIONĀ .

    OK or NG

    1. OK: Go to 18.
    2. NG: Replace EVAP control system pressure sensor.

  19. Check EVAP/ORVR LineĀ 

    Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kink, looseness and improper connection. For location, Refer to ON BOARD REFUELING VAPOR RECOVERY (ORVR)Ā .

    OK or NG

    1. OK: Go to 19.
    2. NG: Repair or replace hoses and tubes.
  20. Check Recirculation LineĀ 

    Check recirculation line between filler neck tube and fuel tank for clogging, kink, cracks, looseness and improper connection.

    OK or NG

    1. OK: Go to 20.
    2. NG: Repair or replace hose, tube or filler neck tube.

  21. Check Refueling EVAP Vapor Cut ValveĀ 

    Refer to COMPONENT INSPECTIONĀ .

    OK or NG

    1. OK: Go to 21.
    2. NG: Replace refueling EVAP vapor cut valve with fuel tank.

  22. Check Intermittent IncidentĀ 

    Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTĀ .

    1. Inspection endĀ 
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.