Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- Check Ground ConnectionsÂ
- Turn ignition switch OFF.
- Loosen and retighten three ground screws on the body. See Figure. Refer to GROUND INSPECTIONÂ .
OK or NG
- OK: Go to 2.
- NG: Repair or replace ground connections.
- Check Throttle Position Sensor 2 Power Supply Circuit-IÂ
- Disconnect electric throttle control actuator harness connector. See Figure.
- Turn ignition switch ON.
- Check voltage between electric throttle control actuator terminal 1 and ground with CONSULT-II or tester.
Voltage: Approximately 5VÂ
OK or NG
- OK: Go to  7.
- NG: Go to 3.
- Check Throttle Position Sensor 2 Power Supply Circuit-IIÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between electric throttle control actuator terminal 1 and ECM terminal 47. Refer to wiring diagram. See Figure.
Continuity should exist .
OK or NG
- OK: Go to 4.
- NG: Repair or replace open circuit.
- Check Throttle Position Sensor 2 Power Supply Circuit-IIIÂ
Check the following.
- Harness for short to power and short to ground, between the following terminals.THROTTLE POSITION SENSOR 2 CIRCUIT TESTS
ECM Terminal Sensor See 47 Electric Throttle Control Actuator Terminal 1 (1) 91 APP Sensor Terminal 2 (2) (1) See WIRING DIAGRAMÂ (2) See WIRING DIAGRAMÂ
OK or NG
- OK: Go to 5.
- NG: Repair short to ground or short to power in harness or connectors.
- Harness for short to power and short to ground, between the following terminals.
- Check APP SensorÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NG
- OK: Go to  11.
- NG: Go to 6.
- Replace Accelerator Pedal AssemblyÂ
- Replace accelerator pedal assembly.
- Perform ACCELERATOR PEDAL RELEASED POSITION LEARNINGÂ .
- Perform THROTTLE VALVE CLOSED POSITION LEARNINGÂ .
- Perform IDLE AIR VOLUME LEARNINGÂ .
- Inspection end
- Check Throttle Position Sensor 2 Ground Circuit For Open And ShortÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between electric throttle control actuator terminal 5 and ECM terminal 66. Refer to wiring diagram. See Figure.
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NG
- OK: Go to 8.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- Check Throttle Position Sensor 2 Input Signal Circuit For Open And ShortÂ
- Check harness continuity between ECM terminal 69 and electric throttle control actuator terminal 2. Refer to wiring diagram. See Figure.
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NG
- OK: Go to 9.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- Check harness continuity between ECM terminal 69 and electric throttle control actuator terminal 2. Refer to wiring diagram. See Figure.
- Check Throttle Position SensorÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NG
- OK: Go to  11.
- NG: Go to 10.
- Replace Electric Throttle Control ActuatorÂ
- Replace the electric throttle control actuator.
- Perform THROTTLE VALVE CLOSED POSITION LEARNINGÂ .
- Perform IDLE AIR VOLUME LEARNINGÂ .
- Inspection endÂ
- Check Intermittent IncidentÂ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
- Inspection endÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
