2021 Hyundai Venue SEFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

  1. Set shift lever to N position.
  2. Turn OFF ignition switch and disconnect the negative (-) battery cable.
  3. Remove the air cleaner and air duct.
    1. Remove the air duct (A).
      G14694748Courtesy of HYUNDAI MOTOR AMERICA
    2. Disconnect the breather hose (B) and air intake hose (C).
    3. Remove the air cleaner assembly (D).

      Tightening torque: 

      Hose clamp bolt (C):

      2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)

      Air cleaner assembly bolts (D):

      3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 lb-ft)

      G14694749Courtesy of HYUNDAI MOTOR AMERICA
  4. Remove the battery (+) terminal (A).

    Tightening torque: 

    7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 Ib-ft)

    G14694750Courtesy of HYUNDAI MOTOR AMERICA
  5. Remove the battery mounting bracket (A) and the battery (B).

    Tightening torque: 

    9.0 - 14.0 N.m (0.9 - 1.4 kgf.m, 6.6 - 10.3 Ib-ft)

    G14694751Courtesy of HYUNDAI MOTOR AMERICA
  6. Remove the ECM.
    1. Disconnect the ECM connector (A).
    2. Loosen the mounting bolts (B) and then removing the ECM bracket assembly.

      Tightening torque: 

      9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G14694752Courtesy of HYUNDAI MOTOR AMERICA
  7. Remove the battery tray.
    1. Loosen the mounting bolt (A) and then removing the battery (+) terminal bracket.

      Tightening torque: 

      8.0 - 10.0 N.m (0.8 - 1.0 kgf.m, 5.9 - 7.4 lb-ft)

      G14694753Courtesy of HYUNDAI MOTOR AMERICA
    2. Loosen the bolts and then removing the battery tray (A).

      Tightening torque: 

      8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 Ib-ft)

    G14694754Courtesy of HYUNDAI MOTOR AMERICA
  8. Separate the control cable.
    1. Remove the snap pin (A).
    2. Separate the select cable (B) and then shift cable (C).
      G14694755Courtesy of HYUNDAI MOTOR AMERICA
  9. Remove the control shaft assembly (A) after loosening the bolts.

    Tightening torque: 

    19.6 - 26.5 N.m (2.0 - 2.7 kgf.m, 14.5 - 19.5 lb-ft)

    G14694756Courtesy of HYUNDAI MOTOR AMERICA
Chapter Navigation
Return to Chapter: Repair Procedures
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.