2021 Hyundai Venue SEFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Installation

CAUTION:
  • Place the shift lever and transaxle side lever in "4th" shift position and insert the lever fixing pin (A).
    G14694731Courtesy of HYUNDAI MOTOR AMERICA
  1. Install the retainer (B) and then tighten the nuts (A).

    Tightening torque: 

    11.8 - 14.7 N.m (1.2 - 1.5 kgf.m, 8.7 - 10.8 lb-ft)

    G14694732Courtesy of HYUNDAI MOTOR AMERICA
  2. Install the shift cable end (A) and the shift lever (B).

    Tightening torque: 

    8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 lb-ft)

    G14694733Courtesy of HYUNDAI MOTOR AMERICA
  3. Install the shift cable (A) from the shift lever.
    G14694734Courtesy of HYUNDAI MOTOR AMERICA
  4. Install the select cable (B) and the snap pin (A).
    G14694735Courtesy of HYUNDAI MOTOR AMERICA
  5. Install the air duct (A).
    G14694736Courtesy of HYUNDAI MOTOR AMERICA
  6. Install the clip (A) of wiring.
    G14694737Courtesy of HYUNDAI MOTOR AMERICA
  7. Move the locker (B) in the direction of "F" with pulling the holder (A) in the direction of "P".
    G14694738Courtesy of HYUNDAI MOTOR AMERICA
  8. Install the control cable.
    1. Install the snap pin (A).
    2. Separate the select cable (B) and then shift cable (C).
    G14694739Courtesy of HYUNDAI MOTOR AMERICA
  9. Tighten the holder (A) to the "P" directions after fixing the rockers (B) in the "F" direction.
    G14694740Courtesy of HYUNDAI MOTOR AMERICA
  10. Remove the shift lever 4th fixing pin (A).
    G14694741Courtesy of HYUNDAI MOTOR AMERICA
  11. Install the floor console assembly.

    (Refer to Body - "FLOOR CONSOLE ")

  12. Install the battery tray.
    1. Tighten the bolts and then install the battery tray (A).

      Tightening torque: 

      8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 Ib-ft)

      G14694742Courtesy of HYUNDAI MOTOR AMERICA
    2. Tighten the mounting bolt (A) and then install the battery (+) terminal bracket.

      Tightening torque: 

      8.0 - 10.0 N.m (0.8 - 1.0 kgf.m, 5.9 - 7.4 lb-ft)

      G14694743Courtesy of HYUNDAI MOTOR AMERICA
  13. Install the ECM.
    1. Connect the ECM connector (A).
    2. Tighten the mounting bolts (B) and then removing the ECM bracket assembly.

      Tightening torque: 

      9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

      G14694744Courtesy of HYUNDAI MOTOR AMERICA
  14. Install the battery (B) and mounting bracket (A).

    Tightening torque: 

    9.0 - 14.0 N.m (0.9 - 1.4 kgf.m, 6.6 - 10.3 Ib-ft)

    G14694745Courtesy of HYUNDAI MOTOR AMERICA
  15. Install the battery (+) terminal (A).

    Tightening torque: 

    7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb-ft)

    G14694746Courtesy of HYUNDAI MOTOR AMERICA
  16. Connect the battery (-) cable.
    CAUTION:
    • Check operating of lever of transaxle side when operating shift lever after assembly. (1~6, R)
    • If there is sticky feel, adjust the control cable length again. (Refer to Manual Transaxle Control System - "CONTROL CABLE ")
Chapter Navigation
Return to Chapter: Repair Procedures
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.