Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Hyundai Venue DenimFACTORY OEM SERVICE PROCEDURE
Front View Camera System DTCS
FRONT VIEW CAMERA SYSTEM DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| C1101-17 | BATTERY VOLTAGE HIGH |
| C1102-16 | Battery Voltage Low |
| C1532-11 | LKAS Switch Failure |
| C1532-15 | LKAS Switch Failure |
| C1532-23 | LKAS Switch Failure |
| C1604-49 | ECU Hardware Error |
| C1606-49 | ECU Software Error |
| C160A-87 | Local CAN Bus Off |
| C1611-08 | CAN Time-Out EMS |
| C1611-87 | CAN Time-Out EMS |
| C1612-08 | CAN Time-Out TCU |
| C1613-02 | CAN Signal Error EMS |
| C1613-86 | CAN Signal Error EMS |
| C1616-87 | C-CAN Bus OFF |
| C1623-08 | CAN Time-out Steering Angle Sensor |
| C1623-85 | CAN Time-out Steering Angle Sensor |
| C1623-87 | CAN Time-out Steering Angle Sensor |
| C1625-08 | CAN Time-Out ABS/ESP |
| C1625-85 | CAN Time-Out ABS/ESP |
| C1625-87 | CAN Time-Out ABS/ESP |
| C1628-08 | CAN Time-Out Cluster |
| C1628-87 | CAN Time-Out Cluster |
| C1642-02 | CAN Signal Error - ABS/ESP |
| C1642-86 | CAN Signal Error - ABS/ESP |
| C1646-02 | CAN Signal Error - TCU |
| C1656-02 | CAN Signal Error - Cluster |
| C1656-86 | CAN Signal Error - Cluster |
| C1672-02 | CAN Signal Error - Steering Angle Sensor |
| C1672-86 | CAN Signal Error - Steering Angle Sensor |
| C1687-85 | CAN Time-Out MDPS |
| C1687-87 | CAN Time-Out MDPS |
| C1688-86 | CAN Signal Error - MDPS |
| C16B6-87 | CAN Time-Out AEB |
| C16B8-02 | CAN Signal Error - AEB |
| C1702-46 | Variant Coding Error |
| C1702-62 | Variant Coding Error |
| C1812-08 | CAN Time-Out Gateway |
| C1812-87 | CAN Time-Out Gateway |
| C1817-02 | CAN Signal Error Gateway |
| C2239-86 | MDPS Steering Control Failure for LKAS |
| C2721-46 | System Calibration Required |
| C2722-46 | System Out of Calibration |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.