2021 Hyundai Veloster 2.0, Automatic TransFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

CAUTION:
  • When Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
  • Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
  • Maintain clean condition so that foreign substance does not get into the automatic transaxle.
  • Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
  • Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
  1. Turn ignition switch OFF and disconnect the negative (-) battery cable.
  2. Remove the air cleaner assembly and air duct.

    (Refer to Engine Mechanical System - "AIR CLEANER ")

  3. Remove the drain plug (A) and drain the ATF totally and then reinstall the drain plug.
    G13055933Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Replace the gasket before reinstalling the drain plug.
    • After the installation, start the engine and then check if there are any leakages from the drain plug.
  4. Remove the wiring mounting clip (A).
  5. Disconnect the air breather hose (B) from the valve body cover.

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13055934Courtesy of HYUNDAI MOTOR AMERICA
  6. Disconnect the hose (A) after removing the automatic transaxle fluid cooler hose clamp.
    G13055935Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Carefully install the clamp not to damage the hose.
    • Install the clamp in a correct direction not to be interfered with other parts.
    • After the installation, start the engine and then check if there are any leakages from the hose.
  7. Remove the valve body cover (A).

    Tightening torque: 

    11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

    G13055936Courtesy of HYUNDAI MOTOR AMERICA
    G13055937Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Replace the gasket (A) before reinstalling the valve body cover.
      G13055938Courtesy of HYUNDAI MOTOR AMERICA
    • After the installation, start the engine and then check if there are any leakages from the valve body cover.
  8. Disconnect the oil temperature sensor and solenoid valve connector (A) from the valve body.

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13055939Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Check for the looseness, poor connection, bending, corrosion, contamination, deterioration, or damage before reinstalling the solenoid valve connector.
  9. Remove the valve body assembly (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13055940Courtesy of HYUNDAI MOTOR AMERICA
  10. Disconnect the input & output speed sensor connector (A).
    G13055941Courtesy of HYUNDAI MOTOR AMERICA
  11. Remove the input & output speed sensor (A) after removing the bolts (2 ea.)

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13055942Courtesy of HYUNDAI MOTOR AMERICA
Chapter Navigation
Return to Chapter: Repair Procedures
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.