Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Hyundai Tucson Value, FWDFACTORY OEM SERVICE PROCEDURE
Antilock Brake System (Abs)/Electronic Stability Control (ESC) System DTCS
ABS/ESC DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| DTC C1101 | Battery Voltage High |
| DTC C1102 | Battery Voltage Low |
| DTC C1113 | 5V Sensor Power Fail |
| DTC C1114 | 12V Sensor Power Fail |
| DTC C1200 | Wheel Speed Sensor Front-LH Open/Short |
| DTC C1201 | Wheel Speed Sensor Front-LH Range/Performance/Intermittent |
| DTC C1202 | Wheel Speed Sensor Front-LH Invalid/no Signal |
| DTC C1203 | Wheel Speed Sensor Front-RH Open/Short |
| DTC C1204 | Wheel Speed Sensor Front-RH Range/Performance/Intermittent |
| DTC C1205 | Wheel Speed Sensor Front-RH Invalid/no Signal |
| DTC C1206 | Wheel Speed Sensor Rear-LH Open/Short |
| DTC C1207 | Wheel Speed Sensor Rear-LH Range/Performance/Intermittent |
| DTC C1208 | Wheel Speed Sensor Rear-LH Invalid/no Signal |
| DTC C1209 | Wheel Speed Sensor Rear-RH Open/Short |
| DTC C1210 | Wheel Speed Sensor Rear-RH Range/Performance/Intermittent |
| DTC C1211 | Wheel Speed Sensor Rear-RH Invalid/no Signal |
| DTC C1235 | Primary Pressure Sensor-Electrical |
| DTC C1237 | Primary Pressure Sensor-Signal |
| DTC C1260 | Steering Angle Sensor Circuit-Signal |
| DTC C1261 | Steering Angle Sensor Not Calibrated |
| DTC C1282 | Yaw Rate & G Sensor-Electrical |
| DTC C1285 | G sensor Calibration Error |
| DTC C1286 | Yaw Rate & G Sensor Fail-Check SRSCM |
| DTC C1358 | AVH not Available due to EPB in Emergency Release |
| DTC C1378 | Pedal Signal Open/Short Error |
| DTC C1379 | Invalid Pedal Signal Error |
| DTC C1380 | Pedal Signal not Calibrated |
| DTC C1385 | Vacuum Sensor-Electrical |
| DTC C1386 | Vacuum Sensor-Signal |
| DTC C1386 | Vacuum Sensor-Signal |
| DTC C1503 | TCS/ESC (ESP) Switch Error |
| DTC C1513 | Brake Switch Error |
| DTC C1520 | Clutch Signal Error |
| DTC C1526 | Down Hill Brake Control (DBC) Switch Error |
| DTC C1527 | Gear R switch Open/Short |
| DTC C1539 | In Gear Switch Error |
| DTC C1604 | ECU Hardware Error |
| DTC C1611 | CAN Time-out EMS |
| DTC C1612 | CAN Time-out TCM |
| DTC C1613 | CAN Wrong Message from ECM |
| DTC C1616 | CAN Bus OFF |
| DTC C1623 | CAN Time-out Steering Angle Sensor |
| DTC C1627 | CAN Time-out 4WD |
| DTC C1628 | CAN Time-out Cluster |
| DTC C1638 | CAN Time-Out SCC |
| DTC C1648 | CAN signal error EMS for SCC (Check EMS) |
| DTC C1649 | CAN time-out EMS for SCC |
| DTC C1650 | CAN signal error SCC |
| DTC C1656 | CAN Signal Error Cluster |
| DTC C1687 | CAN Time-out MDPS |
| DTC C1688 | MDPS signal error |
| DTC C1702 | Variant Coding Error |
| DTC C1713 | Factory Mode Not Disabled |
| DTC C2112 | Valve Relay Error |
| DTC C2202 | Latching Failure/Mechanics |
| DTC C2227 | Excessive Temperature Of Brake Disc |
| DTC C2228 | CAN signal error TCU for SCC |
| DTC C2380 | ABS/TCS/ESC (ESP) Valve Error |
| DTC C2402 | Motor Electrical |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
