Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Hyundai Tucson Limited, FWDFACTORY OEM SERVICE PROCEDURE
TCM Terminal input/output signal
| Pin | Description | Condition | Input/output value | |
|---|---|---|---|---|
| Type | Level | |||
| A1 | Solenoid power 1 | Β | Power | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| A2 | Line pressure control solenoid valve (LINE_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| A3 | Torque converter control solenoid valve (T/CON_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| A4 | 35R clutch control solenoid valve (35R/C_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| A7 | Inhibitor switch signal "S1" | High | Input | 0V/Battery voltage level |
| Low | 9V < Battery voltage level < 16V | |||
| A8 | Inhibitor switch signal "S2" | High | Input | 0V/Battery voltage level |
| Low | 9V < Battery voltage level < 16V | |||
| A9 | Manual mode up switch | Up On | Input | 0V/Battery voltage level |
| Other | 9V < Battery voltage level < 16V | |||
| A22 | Solenoid supply power 2 | Β | Power | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| A23 | Underdrive brake control solenoid valve (UD/B_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| Power supply: V_SOL2 | ||||
| A24 | 26 brake control solenoid valve (26/B_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| Power supply: V_SOL2 | ||||
| A25 | Overdrive clutch control solenoid valve (OD/C_VFS) | - | Output | 0V/Battery voltage level |
| 9V < Battery voltage level < 16V | ||||
| Power supply: V_SOL1 | ||||
| A28 | Inhibitor switch signal "S4" | High | Input | 0V/Battery voltage level |
| Low | 9V < Battery voltage level < 16V | |||
| A29 | Inhibitor switch signal "S3" | High | Input | 0V/Battery voltage level |
| Low | 9V < Battery voltage level < 16V | |||
| A30 | Manual mode select switch | Sports mode | Input | 0V/Battery voltage level |
| Other | 9V < Battery voltage level < 16V | |||
| A31 | Manual mode down switch | Down On | Input | 0V/Battery voltage level |
| Other | 9V < Battery voltage level < 16V | |||
| A48 | Oil temperature sensor (-) | - | Ground | 0V |
| A68 | ON/OFF solenoid valve A (SS-A) | High | Output | 0V/Battery voltage level |
| Low | 9V < Battery voltage level < 16V | |||
| A71 | Input speed sensor signal | High | Input | 0.7V/1.4V |
| Low | ||||
| A72 | Output speed sensor signal | High | Input | 0.7V/1.4V |
| Low | ||||
| A92 | Oil temperature sensor (+) | On | Input | 0V/3.3V |
| Off | ||||
| A93 | Input speed sensor power | On | Power | 0V/9V |
| Off | ||||
| A94 | Output speed sensor power | On | Power | 0V/9V |
| Off | ||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
