Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2020 Hyundai Elantra Value EditionFACTORY OEM SERVICE PROCEDURE
Multi Function Camera DTCS
MULTI FUNCTION CAMERA DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| DTC C1101 | 17: Battery Voltage High |
| DTC C1102 | 16: Battery Voltage Low |
| DTC C1532 | 11: LKAS/LDWS Switch Failure (H/W WIRE TYPE) |
| DTC C1532 | 15: LKAS/LDWS Switch Failure (H/W WIRE TYPE) |
| DTC C1532 | 23: LKAS/LDWS Switch Failure (H/W WIRE TYPE) |
| DTC C1604 | 49: ECU H/W Error |
| DTC C1606 | 49: ECU S/W Error |
| DTC C1611 | 08: CAN Time-out EMS |
| DTC C1611 | 87: CAN Time-out EMS |
| DTC C1612 | 08: CAN Time-out CLU |
| DTC C1613 | 02: Invalid signal of EMS |
| DTC C1613 | 86: Invalid signal of EMS |
| DTC C1616 | 87: CAN bus off |
| DTC C1623 | 08: CAN Time-out SAS |
| DTC C1623 | 85: CAN Time-out of SAS |
| DTC C1623 | 87: CAN Time-out of SAS |
| DTC C1625 | 08: CAN Time-out ABS/ESP |
| DTC C1625 | 85: CAN Time-Out of ABS/ESP |
| DTC C1625 | 87: CAN Time-out of ABS/ESP |
| DTC C1628 | 87: CAN Time-out CLU |
| DTC C1642 | 02: Invalid signal of ABS/ESC |
| DTC C1642 | 86: Invalid signal of ABS/ESP |
| DTC C1646 | 02: Invalid signal of TCU |
| DTC C1656 | 86: Invalid signal of CLU |
| DTC C1672 | 02: Invalid signal of SAS |
| DTC C1672 | 86: Invalid signal of SAS |
| DTC C1687 | 85: CAN Time-Out of MDPS |
| DTC C1687 | 85: CAN Time-Out of MDPS |
| DTC C1687 | 87: CAN Time-out of MDPS |
| DTC C1688 | 86: Invalid signal of MDPS |
| DTC C16B8 | 02: Invalid signal of AEB |
| DTC C1702 | 46: Variant Coding Error |
| DTC C1702 | 62: Variant Coding Error |
| DTC C1812 | 08: CAN Time-out CGW |
| DTC C1812 | 08: CAN Time-out CGW |
| DTC C1812 | 87: CAN Time-out CGW |
| DTC C1817 | 02: Invalid Signal of CGW |
| DTC C2721 | 46: System Calibration Required |
| DTC C2722 | 46: System Out of Calibration |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
