2020 Hyundai Elantra GT BaseFACTORY OEM SERVICE PROCEDURE

Connector [A]

Pin No Description Connected to
1 Injector (Cylinder #3) [High] control output Injector (Cylinder #3)
2 Injector (Cylinder #4) [High] control output Injector (Cylinder #4)
3 Injector (Cylinder #2) [Low] control output Injector (Cylinder #2)
4 -  
5 Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1] heater control output Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]
6 -  
7 Battery power (B+) Battery
8 -  
9 -  
10 -  
11 -  
12 -  
13 -  
14 Cooling fan relay [High] control output Cooling fan relay [High]
15 CVVT Oil Control Valve (OCV) [Bank 1/Exhaust] control output CVVT Oil Control Valve (OCV) [Bank 1/Exhaust]
16 Injector (Cylinder #2) [High] control output Injector (Cylinder #2)
17 Injector (Cylinder #1) [High] control output Injector (Cylinder #1)
18 Injector (Cylinder #3) [Low] control output Injector (Cylinder #3)
19 -  
20 Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2] heater control output Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]
21 -  
22 -  
23 Engine Coolant Temperature Sensor (ECTS) signal input Engine Coolant Temperature Sensor (ECTS)
24 Sensor ground Engine Coolant Temperature Sensor (ECTS)
25 -  
26 Fuel Tank Pressure Sensor (FTPS) signal input Fuel Tank Pressure Sensor (FTPS)
27 Fuel pump relay control output (Without Immobilizer) Fuel pump relay
Canister Close Valve (CCV) control output (Without Immobilizer) Canister Close Valve (CCV)
28 -  
29 -  
30 -  
31 Ignition coil (Cylinder #3) control output Ignition coil (Cylinder #3)
32 Ignition coil (Cylinder #1) control output Ignition coil (Cylinder #1)
33 Injector (Cylinder #1) [Low] control output Injector (Cylinder #1)
34 Fuel Pressure Control Valve (FPCV) [High] control output Fuel Pressure Control Valve (FPCV)
35 ETC motor [-] control output ETC motor
36 -  
37 Knock Sensor (KS) signal input Knock Sensor (KS)
38 Sensor ground Knock Sensor (KS)
39 -  
40 Brake Light switch signal input Brake switch
41 -  
42 -  
43 -  
44 -  
45 CVVT Oil Control Valve (OCV) [Bank 1/Intake] control output CVVT Oil Control Valve (OCV) [Bank 1/Intake]
46 Ignition coil (Cylinder #4) control output Ignition coil (Cylinder #4)
47 Ignition coil (Cylinder #2) control output Ignition coil (Cylinder #2)
48 Injector (Cylinder #4) [Low] control output Injector (Cylinder #4)
49 Fuel Pressure Control Valve (FPCV) [Low] control output Fuel Pressure Control Valve (FPCV)
50 ETC motor [+] control output ETC motor
51 -  
52 -  
53 Brake Test switch signal input Brake switch
54 -  
55 Clutch switch signal input Clutch switch
56 Electric load signal input [Defrost] Alternator
57 Alternator COM signal output Alternator
58 Engine speed signal output Smart Key Control Module
59 Cooling fan relay [Low] control output Cooling fan relay
60 Variable Intake Solenoid (VIS) valve control output Variable Intake Solenoid (VIS) valve
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.