Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2018 Hyundai Ioniq Plug-In HybridFACTORY OEM SERVICE PROCEDURE
Engine Control System
TIGHTENING TORQUES SPECIFICATIONS - ENGINE CONTROL SYSTEM
| Item | kgf.m | N.m | lb-ft |
|---|---|---|---|
| ECM installation bolt | 1.0-1.2 | 9.8-11.8 | 7.2 - 8.7 |
| ECM bracket installation bolt/nut | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| Mass airflow sensor clamp installation bolts | 0.3-0.5 | 2.9-4.9 | 2.2 - 3.6 |
| Mass airflow sensor installation bolts | 0.3-0.5 | 2.9-4.9 | 2.2 - 3.6 |
| Manifold absolute pressure sensor installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| Engine Coolant Temperature Sensor installation | 3.0-4.0 | 29.4 - 39.2 | 21.7-28.9 |
| Crankshaft position sensor installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| Camshaft position sensor (Bank 1/Intake) installation bolt | 0.8-1.2 | 7.8-11.8 | 5.8-8.7 |
| Camshaft position sensor (Bank 1/Exhaust) installation bolt | 0.8-1.2 | 7.8-11.8 | 5.8-8.7 |
| Knock sensor installation bolt | 1.9-2.4 | 18.6-23.5 | 13.7-17.4 |
| Heated oxygen sensor {Bank 1/sensor 1) installation | 4.0 - 5.0 | 39.2-49.1 | 28.9 - 36.2 |
| Heated oxygen sensor {Bank 1/sensor 2) installation | 4.0 - 5.0 | 39.2-49.1 | 28.9 - 36.2 |
| Rail pressure sensor installation | 3.0 - 3.5 | 30.0 - 34.3 | 22.1 - 25.3 |
| Electronic throttle body installation bolt | 0.8-1.0 | 7.8-9.8 | 5.8 - 7.2 |
| Purge Control Solenoid Valve bracket installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| CWT oil control solenoid (Bank 1/Intake) installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| CWT oil control valve (Bank 1/Exhaust) installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
| Ignition coil installation bolt | 1.0 - 1.2 | 9.8-11.8 | 7.2-8.7 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.