Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2012VELOSTER STANDARD TRANSREPAIR AND DIAGNOSISGENERAL INFORMATIONDTC INDEXANTILOCK BRAKE SYSTEM (ABS)/ELECTRONIC STABILITY CONTROL (ESC) DTCS
2012 Hyundai Veloster Standard Trans
Antilock Brake System (Abs)/Electronic Stability Control (ESC) DTCS
2012 Hyundai Veloster Standard TransSECTION Antilock Brake System (Abs)/Electronic Stability Control (ESC) DTCS
ANTILOCK BRAKE SYSTEM (ABS)/ELECTRONIC STABILITY CONTROL (ESC) DIAGNOSTIC TROUBLE CODES (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| DTC C1101 | Battery Voltage High |
| DTC C1102 | Battery Voltage Low |
| DTC C1112 | Sensor source voltage |
| DTC C1200 | Wheel Speed Sensor Front-LH Open/Short |
| DTC C1201 | Wheel Speed Sensor Front-LH Range/Performance/Intermittent |
| DTC C1202 | Wheel Speed Sensor Front-LH Invalid/no Signal |
| DTC C1203 | Wheel Speed Sensor Front-RH Open/Short |
| DTC C1204 | Wheel Speed Sensor Front-RH Range/Performance/Intermittent |
| DTC C1205 | Wheel Speed Sensor Front-RH Invalid/no Signal |
| DTC C1206 | Wheel Speed Sensor Rear-LH Open/Short |
| DTC C1207 | Wheel Speed Sensor Rear-LH Range/Performance/Intermittent |
| DTC C1208 | Wheel Speed Sensor Rear-LH Invalid/no Signal |
| DTC C1209 | Wheel Speed Sensor Rear-RH Open/Short |
| DTC C1210 | Wheel Speed Sensor Rear-RH Range/Performance/Intermittent |
| DTC C1211 | Wheel Speed Sensor Rear-RH Invalid/no Signal |
| DTC C1235 | Primary Pressure Sensor-Electrical |
| DTC C1237 | Primary Pressure Sensor-Signal |
| DTC C1260 | Steering Angle Sensor Circuit-Signal |
| DTC C1261 | Steering Angle Sensor Not Calibrated |
| DTC C1282 | Yaw Rate & Lateral G Sensor-Electrical |
| DTC C1283 | Yaw Rate & Lateral G Sensor-Signal |
| DTC C1285 | Sensor Cluster Change Detection/Uncalibrated |
| DTC C1503 | TCS/ESC (ESP) Switch error |
| DTC C1513 | Brake switch error |
| DTC C1527 | Gear R Switch Error |
| DTC C1604 | ECU Hardware Error |
| DTC C1605 | CAN Hardware error |
| DTC C1611 | CAN Time-out ECM |
| DTC C1612 | CAN Time-out TCM |
| DTC C1613 | CAN Wrong Message |
| DTC C1616 | CAN Bus off |
| DTC C1623 | CAN Time-out Steering Angle Sensor |
| DTC C1687 | CAN Time-out MDPS |
| DTC C1688 | MDPS signal error |
| DTC C2112 | Valve Relay Error |
| DTC C2130 | Brake Lamp Relay Error |
| DTC C2227 | Excessive Temperature Of Brake Disc |
| DTC C2380 | ABS/TCS/ESC (ESP) valve error |
| DTC C2402 | Motor Failure |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.