Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Hyundai Tucson GL, AutomaticFACTORY OEM SERVICE PROCEDURE
Engine Control System Diagnosis (2 Of 2)
- DTC Index
- DTC P0461: Fuel Level Sensor 'A' Circuit Range/Performance
- DTC P0462: Fuel Level Sensor 'A' Circuit Low Input
- DTC P0463: Fuel Level Sensor 'A' Circuit High Input
- DTC P0464: Fuel Level Sensor 'A' Circuit Intermittent
- DTC P0504: Brake Switch 'A' / 'B' Correlation
- DTC P0506: Idle Air Control System - RPM Lower than Expected
- DTC P0507: Idle Air Control System - RPM Higher than Expected
- DTC P0532: A/C Refrigerant Pressure Sensor 'A' Circuit Low Input
- DTC P0533: A/C Refrigerant Pressure Sensor 'A' Circuit High Input
- DTC P0560: System Voltage
- DTC P0562: System Voltage Low
- DTC P0563: System Voltage High
- DTC P0564: Cruise Control Multi - Function Input A Circuit
- DTC P0605: Internal Control Module Read Only Memory (ROM) Error
- DTC P0620: Alternator Control Circuit
- DTC P0625: Generator Field/F Terminal Circuit Low
- DTC P0626: Generator Field/F Terminal Circuit High
- DTC P0630: VIN Not Programmed or Incompatible - ECM/PCM
- DTC P0638: Throttle Actuator Control Range/Performance (Bank 1)
- DTC P0642: Sensor Reference Voltage 'A' Circuit Low
- DTC P0643: Sensor Reference Voltage 'A' Circuit High
- DTC P0650: Malfunction Indicator Lamp (MIL) Control Circuit
- DTC P0652: Sensor Reference Voltage 'B' Circuit Low
- DTC P0653: Sensor Reference Voltage 'B' Circuit High
- DTC P0661: Intake Manifold Tuning Valve Control Circuit Low (Bank 1)
- DTC P0662: Intake Manifold Tuning Valve Control Circuit High (Bank 1)
- DTC P0698: Sensor Reference Voltage 'C' Circuit Low
- DTC P0699: Sensor Reference Voltage 'C' Circuit High
- DTC P06A4: Sensor Reference Voltage 'D' Circuit Low
- DTC P06A5: Sensor Reference Voltage 'D' Circuit High
- DTC P0704: Clutch Switch Input Circuit Malfunction
- DTC P2004: Intake Manifold Runner Control Stuck Open (Bank 1)
- DTC P2006: Intake Manifold Runner Control Stuck Closed (Bank 1)
- DTC P2008: Intake Manifold Runner Control Circuit/Open (Bank 1)
- DTC P200A: Intake Manifold Runner Performance (Bank 1)
- DTC P2016: Intake Manifold Runner Position Sensor/Switch Circuit Low (Bank 1)
- DTC P2017: Intake Manifold Runner Position Sensor/Switch Circuit High (Bank 1)
- DTC P2096: Post Catalyst Fuel Trim System too Lean (Bank 1)
- DTC P2097: Post Catalyst Fuel Trim System too Rich (Bank 1)
- DTC P2101: Throttle Actuator Control Motor Circuit Range/Performance
- DTC P2104: Throttle Actuator Control System - Forced Idle
- DTC P2105: Throttle Actuator Control System-Force Engine Shutdown
- DTC P2106: Throttle Actuator Control System-Force Limited Power
- DTC P2110: Throttle Actuator Control System-Forced Limited RPM
- DTC P2118: Throttle Actuator Control Motor Current Range/Performance
- DTC P2119: Throttle Actuator Control Throttle Body Range/Performance
- DTC P2122: Throttle/Pedal Position Sensor/Switch 'D' Circuit Low Input
- DTC P2123: Throttle/Pedal Position Sensor Switch 'D' Circuit High Input
- DTC P2127: Throttle/Pedal Position Sensor Switch 'E' Circuit Low Input
- DTC P2128: Throttle/Pedal Position Sensor/Switch 'E' Circuit-High Input
- DTC P2138: Throttle/Pedal Position Sensor/Switch D/E Voltage Correlation
- DTC P2159: Vehicle Speed Sensor 'B' Range / Performance (Wheel Speed Sensor)
- DTC P2187: System too Lean at Idle (β Additive) (Bank 1)
- DTC P2188: System too Rich at Idle (Bank 1)
- DTC P2191: System too Lean at Higher Load (Multiple) (Bank 1)
- DTC P2192: System too Rich at Higher Load (Bank 1)
- DTC P2195: O2 Sensor Signal Stuck Lean (Bank 1 Sensor 1)
- DTC P2196: O2 Sensor Signal Stuck Rich (Bank 1 Sensor 1)
- DTC P2237: O2 Sensor Pumping Current Circuit/Open (Bank 1 Sensor 1)
- DTC P2243: O2 Sensor Reference Voltage Circuit/Open (Bank 1 Sensor 1)
- DTC P2251: O2 Sensor Reference Ground Circuit/Open (Bank 1 Sensor 1)
- DTC P2270: O2 Sensor Signal Stuck Lean (Bank 1 Sensor 2)
- DTC P2271: O2 Sensor Signal Stuck Rich (Bank 1 Sensor 2)
- DTC P2297: O2 Sensor Out of Range During Deceleration - (Bank 1 Sensor 1)
- DTC P2414: O2 Sensor Exhaust Sample Error (Bank 1 Sensor 1)
- DTC P2501: EPMD Voltage Rationality
- DTC P2502: Battery Voltage Rationality
- DTC P2503: No Battery Charge
- DTC P2610: ECM/PCM Internal Engine Off Timer Performance
- DTC P2626: O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 Sensor 1)
- DTC U0001: High Speed CAN Communication Bus off
- DTC U0101: Lost Communication With TCM
- DTC U1111: Battery Sensor fault detected by ECU
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
