2011 Hyundai Azera V6-3.3LFACTORY OEM SERVICE PROCEDURE

ICM (Integrated Circuit Module) Relay Box





Inspection

Burglar Alarm Horn
Check for continuity between the terminals.
1. There should be continuity between the No.18 and No.19 terminals when power and ground are connected to the No.8 and No.17 in the ICM-A.
2. There should be no continuity between the No.18 and No.19 terminals when power is disconnected.

Burglar Alarm
Check for continuity between the terminals.
1. There should be no continuity between the No.20 and No.7 terminals when power and ground are connected to the No.20 and No.8 in the ICM-A.
2. There should be continuity between the No.20 and No.7 terminals when power is disconnected.

Adjust Pedal
Check for continuity between the terminals.
1. There should be continuity between the No.11 and No.10 terminals when power and ground are connected to the No.11 and No.4 in the ICM-A.
2. There should be no continuity between the No.11 and No.10 terminals when power is disconnected.

Wiper
Check for continuity between the terminals.
1. There should be continuity between the No.14 and No.16 terminals when power and ground are connected to the No.15 and No.5 terminals in the ICM-A.
2. There should be continuity between the No.14 and No.6 terminals when power is disconnected.

Washer
Check for continuity between the terminals.
1. There should be continuity between the No.15 and No.13 terminals when power and ground are connected to the No.15 and No.12 terminals in the ICM-A.
2. There should be no continuity between the No.15 and No.13 terminals when power is disconnected.

Head Lamp Washer
Check for continuity between the terminals.
1. There should be continuity between the No.1 and No.2 terminals when power and ground are connected to the No.9 and No.3 terminals in the ICM-A.
2. There should be no continuity between the No.1 and No.2 terminals when power is disconnected.

Front Power Socket
Check for continuity between the terminals.
1. There should be continuity between the No.14 and No.15 terminals when power and ground are connected to the No.10 and No.1 terminals in the ICM-B.
2. There should be no continuity between the No.14 and No.15 terminals when power is disconnected.

Rear Seat Power Socket
Check for continuity between the terminals.
1. There should be continuity between the No.13 and No.12 terminals when power and ground are connected to the No.10 and No.1 terminals in the ICM-B.
2. There should be no continuity between the No.13 and No.12 terminals when power is disconnected.

Rear Fog Lamp
Check for continuity between the terminals.
1. There should be continuity between the No.13 and No.12 terminals when power and ground are connected to the No.10 and No.1 terminals in the ICM-B.
2. There should be no continuity between the No.13 and No.12 terminals when power is disconnected.

Tail Lamp
Check for continuity between the terminals.
1. There should be continuity between the No.13 and No.12 terminals when power and ground are connected to the No.10 and No.1 terminals in the ICM-B.
2. There should be no continuity between the No.13 and No.12 terminals when power is disconnected.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.