Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
General Information (Engine Electrical System): Specifications
Ignition System
| Items | Specification | ||
|---|---|---|---|
| Ignition coil | Primary resistance | 0.62 ± 10 % (Ω) | |
| Secondary resistance | 7.0 ± 15 % (kΩ) | ||
| Spark plugs | Unleaded | NGK | IFR5G-11 |
| Gap | 1.0 ~ 1.1 mm (0.0394 ~ 0.0433 in.) | ||
Starting System
| Items | Specification | ||
|---|---|---|---|
| Starter | Rated voltage | 12 V, 1.4 kW | |
| No. of pinion teeth | 8 | ||
| No-load characteristics | Voltage | 11.5 V | |
| Ampere | 85A, MAX | ||
| Speed | 2,600 RPM, MIN | ||
Charging System
| Items | Specification | ||
|---|---|---|---|
| 3.3L | 3.8L | ||
| Alternator | Type | Battery voltage sensing | |
| Rated voltage | 13.5V, 130A A | ||
| Speed in use | 1,000 ~ 18,000 RPM | ||
| Voltage regulator | IC regulator built-in type | ||
| Regulator setting voltage | 4.2 ~ 14.8V | ||
| Temperature compensation | -4 ± 4 mV/°C | ||
| Battery | Type | 54 - 26 GL | 64 - 28 FL |
| Cold cranking amperage [at -18°C(-0.4°F)] | 600 A | 630 A | |
| Reserve capacity | 110 min | 130 min | |
| Specific gravity [at 20°C (68°F)] | 1.280 ± 0.01 | ||
- COLD CRANKING AMPERAGE is the amperage a battery can deliver for 30 seconds and maintain a terminal voltage of 7.2V or greater at a specified temperature.
- RESERVE CAPACITY RATING is amount of time a battery can deliver 25A and maintain a minimum terminal voltage of 10.5V at 26.7°C (80.1°F).
Auto Cruise Control System
| Items | Specification |
|---|---|
| Setting error | Within ± 1.5Km/h on level road |
| Vehicle speed memory variation | No variation |
| Setting time | 0.1sec max |
| Resuming time | 0.1sec max. |
| Minimum operating speed | 40 ± 2Km/h |
| Cancel speed range | 15 ± 2Km/h |
| Maximum memorized speed | 160 ± 2Km/h |
| Pulling force | 127N (13Kgf) |
| Main switch serial resistance value | 3.9kΩ ± 1% |
| Command switch serial resistance value | SET switch : 220Ω ± 1% |
| RESUME switch : 910Ω ± 1% |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.