Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Repair Procedures
- Disconnect the battery negative terminal from the battery.
- Remove the air duct(A).
- Remove the air cleaner assembly.
- Disconnect the breather hose (A).
- Disconnect the ECM connectors (B).
- Disconnect the AFS connector (C) and then remove the air cleaner assembly (D).
Tightening torque
7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)
- Step 4 consist of illustration only
- Remove the under cover (A).
Tightening torque
9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)
- Drain the engine coolant.
Remove the radiator cap to speed draining.
- Remove the engine wiring connectors, the harness protectors and mounting clamps.
- RH front, rear oxygen sensor connectors (A).
- Power steering oil pressure sensor connector (B).
- VIS solenoid valve connector (C).
- RH exhaust camshaft OCV connector (D).
- RH injector connector (E).
- Condenser connector (A).
- RH ignition coil connector (B).
- Knock sensor connector (C).
- LH/RH intake camshaft OCV connector (D).
- LH exhaust camshaft OCV connector (E).
- LH injector connectors (F).
- LH ignition coil connectors (A).
- LH exhaust CMPS connector (B).
- LH front oxygen sensor connector (A).
- Alternator connector (A) and the 'B' terminal cable (B).
- LH intake CMPS connector (A) and the oil pressure switch connector (B).
- PCSV connector (A).
- MAP sensor connector (B).
- RH intake CMPS connector (C).
- ETC connector (D).
- OTS connector (E).
- Knock sensor connector (B) and the RH exhaust CMPS connector (A).
- WTS & gauge unit connector (A).
- LH rear oxygen sensor connector (A) and the CKPS connector (B).
Courtesy of HYUNDAI MOTOR CO.
Courtesy of HYUNDAI MOTOR CO.
Courtesy of HYUNDAI MOTOR CO.
Courtesy of HYUNDAI MOTOR CO.
Courtesy of HYUNDAI MOTOR CO.
- Disconnect the throttle body coolant hoses (A), the brake booster vacuum hose (B) and the fuel hose (C).
Tightening torque :
9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)
- Remove the throttle body (A).
Tightening torque :
9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)
- Remove the surge tank stay (A).
Tightening torque:
27.5 ~ 31.4N.m (2.8 ~ 3.2kgf.m, 20.3 ~ 23.1lb-ft)
- Remove surge tank stay (A).
Tightening torque:
9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)
- Disconnect the LH injector connectors.
- Remove the delivery pipe & injector assembly (A).
- Remove the intake the manifold (A).
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
