Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Hyundai Tiburon SEFACTORY OEM SERVICE PROCEDURE
Engine Control System
TIGHTENING TORQUE SPECIFICATIONS
| Items | N.m | kgf.m | lbf.ft |
|---|---|---|---|
| ECM bracket installation bolt/nut | 3.9 ~ 5.9 | 0.4 ~ 0.6 | 2.9 ~ 4.3 |
| Mass air flow sensor clamp installation | 2.9 ~ 4.9 | 0.3 ~ 0.5 | 2.2 ~ 3.6 |
| Crankshaft position sensor installation bolt | 3.9 ~ 5.9 | 0.4 ~ 0.6 | 2.9 ~ 4.3 |
| Crankshaft position sensor connector bracket installation bolt | 19.6 ~ 21.6 | 2.0 ~ 2.2 | 14.5 ~ 15.9 |
| Crankshaft position sensor wheel installation screw | 4.9 ~ 5.9 | 0.5 ~ 0.6 | 3.6 ~ 4.3 |
| Knock sensor installation bolt | 16.7~ 25.5 | 1.7 ~ 2.6 | 12.3 ~ 18.8 |
| Knock sensor connector bracket installation bolt | 3.9 ~ 5.9 | 0.4 ~ 0.6 | 2.9 ~ 4.3 |
| Engine coolant temperature sensor installation | 19.6 ~ 39.2 | 2.0 ~ 4.0 | 14.5 ~ 28.9 |
| Heated Oxygen Sensor (Bank 1, Sensor 1) | 39.2 ~ 49.1 | 4.0 ~ 5.0 | 28.9 ~ 36.2 |
| Heated Oxygen Sensor (Bank 1, Sensor 2) | 39.2 ~ 49.1 | 4.0 ~ 5.0 | 28.9 ~ 36.2 |
| Heated Oxygen Sensor (Bank 2, Sensor 1) | 39.2 ~ 49.1 | 4.0 ~ 5.0 | 28.9 ~ 36.2 |
| Heated Oxygen Sensor (Bank 2, Sensor 2) | 39.2 ~ 49.1 | 4.0 ~ 5.0 | 28.9 ~ 36.2 |
| Camshaft position sensor installation bolt | 3.9 ~ 5.9 | 0.4 ~ 0.6 | 2.9 ~ 4.3 |
| Oil pressure switch installation | 14.7 ~ 21.6 | 1.5 ~ 2.2 | 10.9~ 15.9 |
| Throttle position sensor installation screws | 1.5 ~ 2.5 | 0.15~ 0.25 | 1.1 ~ 1.8 |
| Idle speed control actuator installation bolts | 5.9 ~ 7.8 | 0.6 ~ 0.8 | 4.3 ~ 5.8 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.