Engine Controls - Service & Adjustment Specifications: Capacities

2003 Hyundai XG350 BaseSECTION Capacities
NOTE: Refill capacities are approximate. Correct fluid level should be determined by mark on dipstick, if applicable.
FLUID CAPACITIES

Application Quantity
Automatic Transaxle (1)
Accent 6.5 Qts. (6.2L)
Elantra 8.2 Qts. (7.8L)
Santa Fe
2.4L 8.2 Qts. (7.8L)
2.7L 8.9 Qts. (8.4L)
3.5L 11.1 Qts. (10.5L)
Sonata 8.2 Qts. (7.8L)
Tiburon 8.2 Qts. (7.8L)
XG350 8.9 Qts. (8.5L)
Cooling System (Includes Heater & Reserve Tank)
Accent 6.9 Qts. (6.5L)
Elantra 6.3 Qts. (6.0L)
Santa Fe
2.4L & 2.7L 7.4 Qts. (7.0L)
3.5L 6.3 Qts. (6.0L)
Sonata
2.4L 5.8 Qts. (5.5L)
2.7L 9.0 Qts (8.5L)
Tiburon
2.0L 7.9 Qts. (7.5L)
2.7L 9.1 Qts. (8.6L)
XG350 8.7 Qts. (8.2L)
Crankcase (Includes Filter)
Accent 3.5 Qts. (3.3L)
Elantra 4.2 Qts. (4.0L)
Santa Fe
2.4L 4.5 Qts. (4.3L)
2.7L 4.8 Qts. (4.5L)
3.5L 4.6 Qts. (4.4L)
Sonata
2.4L 4.2 Qts. (4.0L)
2.5L 4.8 Qts. (4.5L)
Tiburon
2.0L 4.2 Qts. (4.0L)
2.7L 4.8 Qts. (4.5L)
XG350 4.5 Qts. (4.3L)
Manual Transaxle (SAE 75W-90/API GL-4)
Accent 2.3 Qts. (2.2L)
Elantra 2.3 Qts. (2.2L)
Santa Fe
2.4L & 2.7L 2.2 Qts. (2.1L)
3.5L 2.6 Qts. (2.5L)
Sonata 2.3 Qts. (2.2L)
Tiburon 2.3 Qts. (2.2L)
XG350 N/A
Power Steering (PSF-3)
Accent 1.0 Qts. (0.9L)
Elantra 0.8-0.9 Qts. (0.7-0.8L)
Santa Fe 1.1 Qts. (1.0L)
Sonata 1.1 Qts. (1.0L)
Tiburon 0.8-0.9 Qts. (0.7-0.8L)
XG350 1.1 Qts. (1.0L)
(1) Tiburon uses Genuine Hyundai transaxle oil ATF SP-II M or Diamond ATF SP-II M. All other models use Genuine Hyundai transaxle oil ATF SP-III M or Diamond ATF SP-III M.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.