Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSHYUNDAI2003ACCENT L4-1.6LREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTECHNICAL SERVICE BULLETINS
2003 Hyundai Accent L4-1.6L
Computers and Control Systems: Technical Service Bulletins
2003 Hyundai Accent L4-1.6LSECTION Technical Service Bulletins
- Customer Interest
- A/T - MIL ON/DTC's P0705/P0707/P0708/No Start In P/N
- Engine Controls - DTC's P0130/P0503/'R' to 'D' Lurch
- A/T - No Movement in 'DRIVE' or 'REVERSE'
- Exhaust System - Excessive Sulfur Odors
- A/T - MIL ON/Shift Flare/Harsh Engagement/DTC's Set
- A/T - Erratic/Slipping Shifts/MIL ON/DTC's Set
- A/T - Fail Safe Mode/Erratic/Hard Shifting/DTC's Set
- A/T - Harsh Shifts/DTC P1709/P0732/P0733/P0734
- By Symptom
- Abnormal wear/deterioration
- Customer Interest
- A/T - MIL ON/DTC's P0705/P0707/P0708/No Start In P/N
- Engine Controls - DTC's P0130/P0503/'R' to 'D' Lurch
- A/T - No Movement in 'DRIVE' or 'REVERSE'
- Exhaust System - Excessive Sulfur Odors
- A/T - MIL ON/Shift Flare/Harsh Engagement/DTC's Set
- A/T - Erratic/Slipping Shifts/MIL ON/DTC's Set
- A/T - Fail Safe Mode/Erratic/Hard Shifting/DTC's Set
- A/T - Harsh Shifts/DTC P1709/P0732/P0733/P0734
- Erratic Shifting
- False instrument warning light/gauges
- Hard Shifting
- Inoperative
- No shift/Incorrect gear engagement
- Odors
- Out of specification
- Slipping
- All Technical Service Bulletins
- A/T Controls - ECM/TCM Reset And Relearn Adaptive Values
- Engine Controls - ECM Replacement and Testing Procedures
- Computers/Controls - Diagnostic Trouble Code List
- Computers/Controls - OBD-II Trouble Code Table
- A/T, Engine Controls - ECM/TCM Reset/Relearn Procedure
- Engine Controls - ECU Reprogramming Procedure
- A/T Controls - PCM/TCM Reset/Relearn Adaptive Values
- A/T Controls - Resetting PCM/TCM Adaptive Values
- Computers/Controls - OBDII DTC List
- A/T Controls - DTC Diagnostic Information
- Emissions - Supplemental EVAP System Diagnostics
- A/T - MIL ON/DTC's P0705/P0707/P0708/No Start In P/N
- Engine Controls - DTC's P0130/P0503/'R' to 'D' Lurch
- A/T Controls - Reset and Relearn Adaptive Values
- A/T - No Movement in 'DRIVE' or 'REVERSE'
- Exhaust System - Excessive Sulfur Odors
- Transmission Controls - A/T DTC List
- A/T - MIL ON/Shift Flare/Harsh Engagement/DTC's Set
- A/T - Erratic/Slipping Shifts/MIL ON/DTC's Set
- A/T - Fail Safe Mode/Erratic/Hard Shifting/DTC's Set
- A/T - Diagnostic Trouble Codes
- A/T - Harsh Shifts/DTC P1709/P0732/P0733/P0734
- A/T - DTC's P0731/P0732/P0733/P0734/P0735/P0736
- A/T - TCM Adaptive Learning Procedure
- Engine Controls - Idle Speed Control Resistance Values
- A/T - Diagnostic Trouble Codes and Scanned Data
- Engine Controls - Service Manual Revision
- Engine Controls - O2 Sensor Connector Guidelines
- Engine Controls - Oxygen Sensor Function/Diagnosis
- Engine Controls - Revised Main Relay
- A/T - No Movement In Drive/Reverse
- A/T Controls - Neutral Position Switch Adaptive Relearn
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.