2000 Hyundai Tiburon AutomaticFACTORY OEM SERVICE PROCEDURE

Connector Identification

Harness connector terminal identification illustrations are generic and categorized by the number of terminals. All connector views are from the component side unless otherwise specified. For harness connector terminal identification, see appropriate HARNESS CONNECTOR IDENTIFICATION DIRECTORY table.

HARNESS CONNECTOR IDENTIFICATION DIRECTORY (ACCENT)

Component Harness Side Component Side
Acceleration Sensor N/A See Fig 1
Camshaft Position (CMP) Sensor See Fig 3 See Fig 2
Crankshaft Position (CKP) Sensor N/A See Fig 1
Diagnosis Module For Tank Leakage (DM-TL) N/A N/A
ECM Connector See Fig 14 See Fig 14
Engine Coolant Temperature (ECT) Sensor See Fig 3 See Fig 2
EVAP Purge Control Solenoid N/A See Fig 1
Fuel Injector N/A See Fig 1
Fuel Tank Pressure (FTP) Sensor See Fig 3 See Fig 2
Heated Oxygen Sensor (HO2S) See Fig 7 See Fig 8
Idle Speed Control (ISC) Actuator See Fig 3 See Fig 2
Ignition Coil N/A See Fig 1
Intake Air Temperature (IAT) Sensor See Fig 9 N/A
Knock Sensor (KS) N/A See Fig 1
Mass Airflow (MAF) Sensor See Fig 9 N/A
Throttle Position (TP) Sensor See Fig 3 See Fig 2
Transaxle Range Switch N/A See Fig 11
Vehicle Speed Sensor (VSS) See Fig 12 See Fig 12
HARNESS CONNECTOR IDENTIFICATION DIRECTORY (ELANTRA & TIBURON)

Component Harness Side Component Side
Acceleration Sensor See Fig 3 See Fig 2
Camshaft Position (CMP) Sensor See Fig 3 See Fig 2
Canister Close (CC) Valve N/A See Fig 1
Crankshaft Position (CKP) Sensor See Fig 3 See Fig 2
ECM Connector See Fig 15 N/A
Engine Coolant Temperature (ECT) Sensor N/A See Fig 1
EVAP Purge Control Solenoid N/A See Fig 1
Fuel Injector N/A See Fig 1
Fuel Tank Pressure (FTP) Sensor See Fig 3 See Fig 2
Heated Oxygen Sensor (HO2S) See Fig 7 See Fig 8
Idle Speed Control (ISC) Actuator See Fig 3 See Fig 2
Ignition Coil See Fig 3 See Fig 2
Intake Air Temperature (IAT) Sensor N/A See Fig 1
Knock Sensor (KS) See Fig 3 See Fig 2
Mass Airflow (MAF) Sensor N/A See Fig 6
Throttle Position (TP) Sensor See Fig 3 See Fig 2
Transaxle Range Switch (A/T) N/A See Fig 11
Vehicle Speed Sensor (VSS) See Fig 13 N/A
HARNESS CONNECTOR IDENTIFICATION DIRECTORY (SONATA)

Component Harness Side Component Side
Camshaft Position (CMP) Sensor See Fig 2 See Fig 3
Canister Close (CC) Valve N/A See Fig 1
Crankshaft Position (CKP) Sensor
2.4L
See Fig 5		 See Fig 4
2.5L See Fig 2 See Fig 3
ECM Connector
2.4L A/T See Fig 16 N/A
2.4L M/T See Fig 17 N/A
2.5L See Fig 18 N/A
EGR Solenoid Valve
2.4L N/A See Fig 1
Engine Coolant Temperature (ECT) Sensor N/A See Fig 1
EVAP Purge Control Solenoid N/A See Fig 1
Fuel Injector N/A See Fig 1
Fuel Tank Pressure (FTP) Sensor See Fig 2 See Fig 3
Heated Oxygen Sensor (HO2S)
2.4L
California (Front & Rear) See Fig 7 See Fig 8
Federal (Front & Rear) See Fig 8 See Fig 7
2.5L (Front & Rear) See Fig 8 See Fig 7
Idle Speed Control (ISC) Actuator See Fig 3 See Fig 2
Ignition Coil
2.4L See Fig 3 See Fig 2
2.5L See Fig 8 See Fig 7
Intake Air Temperature (IAT) Sensor
2.4L See Fig 9 N/A
2.5L N/A See Fig 1
Knock Sensor (KS)
2.4L N/A See Fig 1
2.5L See Fig 3 See Fig 2
Mass Airflow (MAF) Sensor
2.4L See Fig 9 N/A
2.5L See Fig 3 See Fig 2
Manifold Absolute Pressure (MAP) Sensor N/A See Fig 6
Throttle Position (TP) Sensor
2.4L N/A (1) See Fig 6
2.5L See Fig 3 See Fig 2
Transaxle Range Switch (2.4L A/T) See Fig 10 N/A
Vehicle Speed Sensor (VSS) See Fig 3 See Fig 2
(1) Includes Idle Position Switch.
Fig 1: Identifying 2-Pin Connector Male Terminals
G98H11376Courtesy of HYUNDAI MOTOR CO.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.