1999 Hyundai Tiburon Base, AutomaticFACTORY OEM SERVICE PROCEDURE

Engine Controls - Service & Adjustment Specifications: Capacities

BATTERY SPECIFICATIONS

Application Group (1) CCA Rating
Accent (1.5L) (2) MF55Ah 433Ah Or More
Elantra (2.0L) (3) MF60Ah 550Ah Or More
Sonata
2.4L (4) MF68Ah 550Ah Or More
2.5L (4) MF68Ah 540Ah Or More
Tiburon (2.0L) (3) MF68Ah 600Ah Or More
(1) Cold Cranking Amperage (CCA) is amperage battery can delivery for 30 seconds and maintain a terminal voltage of 7.2 volts or more at 0Β°F (-17.8Β°C).
(2) With 75-amp generator.
(3) With 90-amp generator.
(4) With 95-amp generator.
NOTE: Refill capacities are approximate. Correct fluid level should be determined by mark on dipstick, if applicable.
FLUID CAPACITIES

Application Quantity
Automatic Transaxle (1)
Accent (1.5L) 6.8 Qts. (6.5L)
Elantra (2.0L) 6.9 Qts. (6.6L)
Sonata
2.4L 8.2 Qts. (7.8L)
2.5L 8.2 Qts. (7.8L)
Tiburon (2.0L) 6.9 Qts. (6.6L)
Cooling System (Includes Heater & Reserve Tank)
Accent (1.5L) 5.7 Qts. (5.4L)
Elantra (2.0L) 6.3 Qts. (6.0L)
Sonata
2.4L 5.8 Qts. (5.8L)
2.5L 5.8 Qts. (5.8L)
Tiburon (2.0L) 6.3 Qts. (6.0L)
Crankcase (Includes Filter)
Accent (1.5L) 3.5 Qts. (3.3L)
Elantra (2.0L) 4.2 Qts. (4.0L)
Sonata
2.4L 4.2 Qts. (4.0L)
2.5L 4.8 Qts. (4.5L)
Tiburon (2.0L) 4.2 Qts. (4.0L)
Manual Transaxle (SAE 75-85W/API GL-4)
Accent (1.5L) 2.3 Qts. (2.2L)
Elantra (2.0L) 2.3 Qts. (2.2L)
Sonata
2.4L 2.2 Qts. (2.1L)
2.5L 2.2 Qts. (2.1L)
Tiburon (2.0L) 2.3 Qts. (2.2L)
Power Steering (Dexron-II) 1.0 Qt. (0.9L)
(1) Use Genuine Hyundai ATF SP-II or equivalent.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.