Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Hummer H3 Base, StandardFACTORY OEM SERVICE PROCEDURE
Manual Transmission
- Specifications
- Fastener Tightening Specifications
- Adhesives, Fluids, Lubricants, and Sealers
- Lubrication Specifications
- Transmission Clearance Specifications
- 1st and 2nd Gear Synchronizer Retaining Ring Specifications
- 3rd and 4th Gear Synchronizer Retaining Ring Specifications
- 5th Gear Synchronizer Retaining Ring Specifications
- Countershaft Front Bearing Retaining Ring Specifications
- Input Shaft Bearing Retaining Ring Specifications
- Fifth Gear Retaining Ring Specifications
- Component Resistance
- Schematic and Routing Diagrams
- Visual Identification
- Diagnostic Information and Procedures
- Diagnostic Code Index
- Diagnostic Starting Point - Manual Transmission
- DTC P0502 or P0503
- DTC P0806
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Typical Scan Tool Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC P0807 or P0808
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Typical Scan Tool Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the MIL/DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC P080A
- Clutch Pedal Position Sensor Learn
- Symptoms - Manual Transmission
- Transmission Shifts Hard
- Transmission Gear Clash When Shifting Gears
- Transmission Noisy
- Transmission Does Not Shift into One Gear
- Transmission Jumps Out of Gear
- Transmission Locked in One Gear
- Transmission Clunk on Acceleration or Deceleration
- Transmission Fluid Leak Diagnosis
- Repair Instructions - On Vehicle
- Transmission Fluid Replacement
- Control Lever and/or Boot Replacement
- Shift Lever Assembly Replacement
- Vehicle Speed Sensor Replacement
- Transmission Mount Replacement
- Input Shaft Bearing Retainer Replacement
- Transmission Input Shaft Seal Replacement
- Transmission Housing Oil Seal Replacement - Rear
- Backup Lamp Switch Replacement
- Transmission Replacement
- Repair Instructions - Off Vehicle
- Transmission Disassemble
- Output Shaft Disassemble
- Input Shaft Disassemble
- Counter Gear Shaft Disassemble
- Shift Control Housing Disassemble
- Transmission Case Disassemble
- Transmission Extension Disassemble
- Synchronizers Disassemble
- Gears and Shafts Cleaning and Inspection
- Bearings and Spacers Cleaning and Inspection
- Synchronizers Cleaning and Inspection
- Shift Shaft and Shift Fork Cleaning and Inspection
- Transmission Case Cleaning and Inspection
- Shift Control Housing Cleaning and Inspection
- Synchronizers Assemble
- Transmission Extension Assemble
- Transmission Case Assemble
- Shift Control Housing Assemble
- Counter Gear Shaft Assemble
- Input Shaft Assemble
- Output Shaft Assemble
- Transmission Assemble
- Description and Operation
- Special Tools and Equipment
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
