2007 Hummer H2 4D Utility PickupFACTORY OEM SERVICE PROCEDURE

Powertrain Control Module (PCM) Connector End View - C2

Fig 1: Powertrain Control Module (PCM) C2 Connector End View
GM684875Courtesy of GENERAL MOTORS CORP.
Powertrain Control Module (PCM) C2 Connector Parts Information

Connector Part Information 
  • OEM: 15492640
  • Service: See Catalog
  • Description: 80-Way F Micro-Pack 100 W Sealed (GN)
Powertrain Control Module (PCM) - C2 Connector Terminal Identification

Pin Wire Color Circuit No. Function
1 BK/WH 451 Ground
2 BN 418 TCC PWM Solenoid Valve Control
3-5 - - Not Used
6 RD/BK 1228 PC Solenoid Valve High Control (Sol. A)
7 - - Not Used
8 L-BU/WH 1229 PC Solenoid Valve Low Control (Sol. A)
9 D-GN/WH 465 Fuel Pump Relay Control
10 WH 121 Engine Speed Signal
11-13 - - Not Used
14 RD/BK 380 A/C Refrigerant Pressure Sensor Signal
15 BN 25 Charge Indicator Control
16 GY/BK 1694 4WD Low Signal
17-19 - - Not Used
20 L-GN/BK 822 VSS Low Signal
21 PU/WH 821 VSS High Signal
22-24 - - Not Used
25 TN 472 IAT Sensor Signal
26 PU 2121 IC 1 Control
27 RD 2127 IC 7 Control
28 L-BU/WH 2126 IC 6 Control
29 D-GN/WH 2124 IC 4 Control
30 - - Not Used
31 YE 492 MAF Sensor Signal
32 L-GN 432 MAP Sensor Signal
33 - - Not Used
34 D-GN/WH 428 EVAP Canister Purge Solenoid Control
35-38 - - Not Used
39 RD 631 12-Volt Reference
40 BK/WH 451 Ground
41 - - Not Used
42 TN/BK 422 TCC Solenoid Valve Control
43 D-GN/WH 459 A/C Compressor Clutch Relay Control
44 - - Not Used
45 WH 1310 EVAP Canister Vent Solenoid Control
46 BN/WH 419 MIL Control
47 YE/BK 1223 Shift Solenoid B Valve Control
48 L-GN 1222 Shift Solenoid A Valve Control
49 - - Not Used
50 D-GN/WH 817 Vehicle Speed Signal
51 YE/BK 1227 TFT Sensor Signal
52 BN 2391 HO2S Heater Low Control - Bank 1 Sensor 2
53 RD/WH 3223 HO2S Heater Low Control - Bank 2 Sensor 2
54 PU/WH 1589 Fuel Level Sensor Signal
55-56 - - Not Used
57 BK 552 Low Reference
58 TN/WH 332 Oil Pressure Sensor Signal
59 PU 806 Crank Voltage
60 BN 2129 Low Reference
61 BN/WH 2130 Low Reference
62 GY 773 Transmission Range Switch Signal C
63 PK 1224 Transmission Fluid Pressure Switch Signal A
64 D-GN 890 Fuel Tank Pressure Sensor Signal
65 - - Not Used
66 PU/WH 2128 IC 8 Control
67 RD/WH 2122 IC 2 Control
68 D-GN 2125 IC 5 Control
69 L-BU 2123 IC 3 Control
70-71 - - Not Used
72 BK/WH 3113 HO2S Heater Low Control - Bank 1 Sensor 1
73 - - Not Used
74 L-GN 3212 HO2S Heater Low Control - Bank 2 Sensor 1
75 GY 23 Generator Field Duty Cycle Signal
76-79 - - Not Used
80 BK 2751 Low Reference
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.