Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Hummer H2 4D Utility PickupFACTORY OEM SERVICE PROCEDURE
Power Door Systems Component Views
| Callout | Component Name |
|---|---|
| 1 | Driver Door |
| 2 | Outside Rearview Mirror |
| 3 | Memory/Heated Seat Switch |
| 4 | Driver Door Module (DDM) Connector - C5 |
| 5 | Driver Door Module (DDM) |
| 6 | Fuse Block - I/P - C3 |
| 7 | Speaker - LF Door |
| 8 | Window Motor - Driver |
| 9 | Door Courtesy Lamp - LF |
| 10 | Door Latch Assembly - Driver |
| 11 | Door Lock Cylinder |
| Callout | Component Name |
|---|---|
| 1 | Passenger Door |
| 2 | Outside Rearview Mirror |
| 3 | Passenger Door Module (PDM) |
| 4 | Door Latch Assembly - Passenger |
| 5 | Door Courtesy Lamp - RF |
| 6 | Window Motor - Passenger |
| 7 | Speaker - RF Door |
| 8 | Junction Block - I/P - C2 |
| 9 | Junction Block - I/P - C7 |
| 10 | Heated Seat Switch |
| Callout | Component Name |
|---|---|
| 1 | Door Latch Assembly - LR |
| 2 | Window Motor - LR |
| 3 | Window Switch - LR |
| 4 | C310 |
| 5 | Speaker - LR |
| 6 | Door Courtesy Lamp - LR |
| Callout | Component Name |
|---|---|
| 1 | Window Motor - RR |
| 2 | Door Latch Assembly - RR |
| 3 | Door Courtesy Lamp - RR |
| 4 | Speaker - RR |
| 5 | C390 |
| 6 | Window Switch - RR |
| Callout | Component Name |
|---|---|
| 1 | Right B-Pillar |
| 2 | C390 |
| 3 | G306 |
| 4 | Liftgate Lock Relay (Except SUT) |
| 5 | Courtesy Lamp - Right B-Pillar |
| 6 | Body Harness |
| Callout | Component Name |
|---|---|
| 1 | Center High Mounted Stop Lamp (CHMSL) Connector |
| 2 | Rear Window Defogger Grid Connector |
| 3 | Rear Window Defogger Grid Connector |
| 4 | Splice S900 |
| 5 | Rear Window Wiper Module - w/Motor |
| 6 | Door Lock Actuator - Liftgate |
| 7 | Liftgate Ajar Switch - Left |
| 8 | Liftgate Ajar Switch - Right |
| 9 | Splice S902 |
| 10 | Splice S901 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
