Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Hummer H2FACTORY OEM SERVICE PROCEDURE
ABS Connector End Views
Electronic Brake Control Module (EBCM) Connector End View
| Β Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | BRN | 882 | Right Rear Wheel Speed Sensor Signal |
| 2 | WHT | 883 | Right Rear Wheel Speed Sensor Low Reference |
| 3 | - | - | Not Used |
| 4 | DK GRN | 872 | Right Front Wheel Speed Sensor Signal |
| 5 | TAN | 833 | Right Front Wheel Speed Sensor Low Reference |
| 6 | LT BLU | 1320 | CHMSL Supply Voltage/Stop Lamp Supply Voltage |
| 7 | - | - | Not Used |
| 8 | PNK | 1339 | Ignition 1 Voltage |
| 9 | PPL | 333 | Brake Fluid Level Sensor Signal |
| 10 | DK BLU | 716 | LNG Rate Signal |
| 11 | LT BLU | 2206 | Traction Control Preference Switch Signal |
| 12 | BLK | 2150 | Ground |
| 13 | RED | 442 | Battery Positive Voltage |
| 14 | ORN | 2340 | Battery Positive Voltage |
| 15 | BLK | 2851 | Ground |
| 16 | ORN | 2554 | Traction Control Preference Switch Indicator |
| 17 | - | - | Not Used |
| 18 | LT BLU | 2088 | LNG Rate Low Reference |
| 19 | - | - | Not Used |
| 20 | LT BLU | 830 | Left Front Wheel Speed Sensor Signal |
| 21 | YEL | 873 | Left Front Wheel Speed Sensor Low Reference |
| 22 | BLK | 884 | Left Rear Wheel Speed Sensor Signal |
| 23 | RED | 885 | Left Rear Wheel Speed Sensor Low Reference |
| 24 | - | - | Not Used |
| 25 | LT BLU | 1122 | ABS/TCS Class 2 Serial Data |
| 26-27 | - | - | Not Used |
| 28 | DK GRN | 2087 | LNG Rate Sensor 5 Volt Reference |
| 29-30 | - | - | Not Used |
Longitudinal Accelerometer Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| 1 | LT BLU | 2088 | LNG Rate Low Reference |
| 2 | DK BLU | 716 | LNG Rate Signal |
| 3 | DK GRN | 2087 | LNG Rate Sensor 5 Volt Reference |
Traction Control Switch Connector End View
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT BLU | 2206 | Traction Control Preference Switch Signal |
| B | BLK/WHT | 1851 | Ground |
| C | ORN | 2554 | Traction Control Preference Switch Indicator |
| D | PPL/WHT | 1382 | LED Dimming Supply |
| E | BRN/WHT | 230 | Instrument Panel Lamps Dimming Control |
| F | PNK | 639 | Ignition 1 Voltage |
Wheel Speed Sensor (WSS) Connector End View - LF
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | LT BLU | 830 | Left Front Wheel Speed Sensor Signal |
| B | YEL | 873 | Left Front Wheel Speed Sensor Low Reference |
Wheel Speed Sensor (WSS) Connector End View - LR
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BLK | 884 | Left Rear Wheel Speed Sensor Signal |
| B | RED | 885 | Left Rear Wheel Speed Sensor Low Reference |
Wheel Speed Sensor (WSS) Connector End View - RF
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | DK GRN | 872 | Right Front Wheel Speed Sensor Signal |
| B | TAN | 833 | Right Front Wheel Speed Sensor Low Reference |
Wheel Speed Sensor (WSS) Connector End View - RR
| Connector Part Information |
|
||
|---|---|---|---|
| Pin | Wire Color | Circuit No. | Function |
| A | BRN | 882 | Right Rear Wheel Speed Sensor Signal |
| B | WHT | 883 | Right Rear Wheel Speed Sensor Low Reference |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
