2021 Honda Pilot EliteFACTORY OEM SERVICE PROCEDURE

Crankshaft Main Bearing: Replacement

  1. Engine/Transmission - Remove - Refer to:

    ENGINE (6-Speed A/T) ('16-'18 9-Speed A/T) - Removal and Installation or

    ENGINE (9-Speed A/T) (2019 2020 2021) - Removal and Installation .

  2. Transmission - Remove - Refer to:

    Automatic Transmission - Removal and Installation (6-Speed A/T) or

    Automatic Transmission - Removal and Installation (9-Speed A/T) .

  3. Drive Plate - Remove - Refer to:

    Drive Plate (6-Speed A/T) ('16-'18 9-Speed A/T) - Removal and Installation

    Drive Plate (9-Speed A/T) (2019 2020 2021) - Removal and Installation

  4. Cylinder Head - Remove - Refer to:

    Cylinder Head (6-Speed A/T), ('16-'18 9-Speed A/T) - Removal and Installation or

    Cylinder Head (9-Speed A/T) (2019 2020 2021) - Removal and Installation .

  5. Oil Pan - Remove
  6. Oil Pump - Remove
  7. Main Bearing Cap and Bearing Half - Remove 
  8. Main Bearing Clearance - Inspect
    Fig 1: Crankshaft Main Bearing Replacement Loosening Sequence
    GHH308267Courtesy of HONDA, U.S.A., INC.
    1. Clean each main journal and the bearing half with a clean shop towel.

    2. Place one strip of plastigage across each main journal.

    NOTE:  If the engine is still in the vehicle when you bolt the main cap down to check the clearance, the weight of the crankshaft and the drive plate will flatten the plastigage further than just the torque on the cap bolt and give you an incorrect reading. For an accurate reading, support the crank with a jack under the counterweights, and check only one bearing at a time.

    3. Reinstall the main bearings and the main bearing caps, then torque the bearing cap bolts to 40 Nm (4.1 Kgf-m, 30 lbf.ft) + 47°, and the bearing cap side bolts to 49 Nm (5.0 Kgf-m, 36 lbf.ft) in the proper sequence.

    NOTE:

    • Apply new engine oil to the bolt threads and flanges.
    • Do not rotate the crankshaft during inspection.
    GHH308268Courtesy of HONDA, U.S.A., INC.
    4. Remove the main bearing caps and the bearing halves, and measure the widest part of the plastigage.
     
    Main Bearing-to-Journal Oil Clearance 
    Standard (New): 0.019-0.045 mm (0.00075-0.00177 in) 
    Service Limit: 0.050 mm (0.00197 in) 

    5. If the plastigage measures too wide or too narrow, remove the crankshaft, and remove the upper half of the bearing. Install a new, complete bearing with the same color code, and recheck the clearance. Do not file, shim, or scrape the bearings or the caps to adjust clearance.

    6. If the plastigage shows the clearance is still incorrect, try the next larger or smaller bearing (the color listed above or below that one), and check the clearance again. If the proper clearance cannot be obtained by using the appropriate larger or smaller bearings, replace the Crankshaft - Removal and Installation  and start over.

  9. Crankshaft Main Bearing - Select
    Block Bore Code Locations 
    GHH308269GHH308270GHH308271Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.

    Main Journal Code Locations 

    GHH308269GHH308270GHH308271Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.
    Factory Service Tools

    Use the Manual With the Right Hardware

    Pair factory procedures with proven DIY tools so the instructions are easier to execute.

    Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

    When to See a Mechanic

    Stop DIY work and contact a certified mechanic immediately if any of the following apply:

    • • You smell fuel, burning insulation, or see smoke.
    • • Brakes feel soft, pull hard to one side, or make grinding noises.
    • • The engine overheats, stalls repeatedly, or misfires under load.
    • • You are missing required tools, torque specs, or safe lifting equipment.
    • • You are not confident in the next step or safety outcome.