2011 Honda Odyssey EXFACTORY OEM SERVICE PROCEDURE

DTC U128D (Body Control Module)

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2025 Honda Odyssey, 2024 Honda Odyssey, 2023 Honda Odyssey, 2022 Honda Odyssey, and 2021 Honda Odyssey. However, it is still accessible from the selected car via links, so may be relevant.

DTC U128D  : BCM (Body Control Module) Lost Communication with Gauge Control Module

NOTE: 

  • If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A .
  • According to the detected DTC (s), check for the power circuit and the ground circuit of the control unit which cannot communicate with the body control module.
  • Refer to the DTC shown on the display, then inspect the connectors and terminals based on the instructions.
DTC Description DTC
U128D BCM (Body Control Module) Lost Communication with Gauge Control Module  

DTC (Body Control Module)

  1. Problem verification

    -1. Turn the vehicle to the ON mode.

    -2. Clear the DTCs with the HDS.

    -3. Turn the vehicle to the OFF (LOCK) mode and then the ON mode.

    -4. Wait for at least 6 seconds.

    -5. Check for DTCs with the HDS.

    DTC Description DTC
    U128D BCM (Body Control Module) Lost Communication with Gauge Control Module  

    Is DTC U128D indicated?

    YES 

    Go to step 2.

    NO 

    Intermittent failure, the system is OK at this time. Check for loose or poor connections.

  2. Open wire check (B-CAN H line, B-CAN L line)

    -1. Turn the vehicle to the OFF (LOCK) mode.

    -2. Disconnect the receiving control unit connector.

    Body control module connector B (36P)

    -3. Disconnect the transmitting control unit connector (s).

    Refer to the DTC shown on the display, then disconnect the connector (s) based on the instructions (see chart below).

    DTC Connector
    U128D Gauge control module connector A (32P)

    -4. Check for continuity between the receiving control unit and the transmitting control unit on the B-CAN H circuit and the B-CAN L circuit.

    Test condition Vehicle OFF (LOCK) mode
    Body control module connector B (36P): disconnected
    Transmitting control unit connector (s) for indicated DTCs: disconnected
    DTC Circuit name Receiving control unit Transmitting control unit
    Connector Terminal Connector Terminal
    U128D B-CAN H Body control module connector B (36P) No. 20 Gauge control module connector A (32P) No. 30
    B-CAN L No. 21 No. 31

    Is there continuity?

    YES 

    The B-CAN H wire and the B-CAN L wire are OK. Refer to the DTC shown on the display, then substitute or replace the control unit based on the instructions (see chart below).

    DTC Operation for transmitting control unit
    U128D Substitute a known-good gauge control module , then recheck. If DTC U128D goes away after substitution, replace the original gauge control module .

    NO 

    Repair an open in the B-CAN H wire and/or the B-CAN L wire between the body control module and the transmitting control unit.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.