Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Honda Insight BaseFACTORY OEM SERVICE PROCEDURE
DTC Troubleshooting Index
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information (see GENERAL TROUBLESHOOTING INFORMATION
).
DTC TROUBLESHOOTING CHART
| DTC(1) | Two Drive Cycle Detection | D Indicator | MIL | Detection Item | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P0107 (12) | - | Blinks | ON | Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage | ||||||||||
| P0108 (02) | - | Blinks | ON | Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage | ||||||||||
| P0335 (88) | - | Blinks | ON | Crankshaft Position (CKP) Sensor No Signal | ||||||||||
| P0336 (88) | - | Blinks | ON | Range/Performance Problem in Crankshaft Position (CKP) Sensor Circuit | ||||||||||
| P0501 (36)(2) | - | Blinks | ON | Range/Performance Problem in CVT Speed Sensor Circuit | ||||||||||
| P0502 (36)(2) | - | Blinks | ON | Problem in CVT Speed Sensor Circuit | ||||||||||
| P062F (-) | - | Blinks | ON | Powertrain Control Module (PCM) Internal Control Module Error | ||||||||||
| P0705 (5)(2) | - | Blinks | ON | Short in Transmission Range Switch Circuit (Multiple Shift-position Input) | ||||||||||
| P0706 (6)(2) | ◦ | OFF | ON | Open in Transmission Range Switch Circuit | ||||||||||
| P0716 (34)(2) | - | Blinks | ON | Range/Performance Problem in CVT Input Shaft (Drive Pulley) Speed Sensor Circuit | ||||||||||
| P0717 (34)(2) | - | Blinks | ON | Problem in CVT Input Shaft (Drive Pulley) Speed Sensor Circuit (No Signal Input) | ||||||||||
| P0721 (35)(2) | - | Blinks | ON | Range/Performance Problem in CVT Output Shaft (Driven Pulley) Speed Sensor Circuit | ||||||||||
| P0722 (35)(2) | - | Blinks | ON | Problem in CVT Output Shaft (Driven Pulley) Speed Sensor Circuit (No Signal Input) | ||||||||||
| P0746 (104) | ◦ | Blinks | ON | CVT Drive Pulley Pressure Control Valve Stuck OFF | ||||||||||
| P0777 (105) | ◦ | Blinks | ON | CVT Driven Pulley Pressure Control Valve Stuck ON | ||||||||||
| P0796 (103) | ◦ | Blinks | ON | CVT Start Clutch Pressure Control Valve Stuck OFF | ||||||||||
| P0962 (38)(2) | - | Blinks | ON | CVT Drive Pulley Pressure Control Valve Circuit Low Voltage | ||||||||||
| P0963 (38)(2) | - | Blinks | ON | CVT Drive Pulley Pressure Control Valve Circuit High Voltage | ||||||||||
| P0966 (39)(2) | - | Blinks | ON | CVT Driven Pulley Pressure Control Valve Circuit Low Voltage | ||||||||||
| P0967 (39)(2) | - | Blinks | ON | CVT Driven Pulley Pressure Control Valve Circuit High Voltage | ||||||||||
| P0970 (32)(2) | - | Blinks | ON | CVT Start Clutch Pressure Control Valve Circuit Low Voltage | ||||||||||
| P0971 (32)(2) | - | Blinks | ON | CVT Start Clutch Pressure Control Valve Circuit High Voltage | ||||||||||
| P16C0 (-) | - | OFF | ON | Powertrain Control Module (PCM) CVT Control System Incomplete Update | ||||||||||
| P16D7 (107) | - | Blinks | OFF | Powertrain Control Module (PCM) Internal F-CAN Communication Circuit Malfunction | ||||||||||
| P16D8 (120) | - | Blinks | ON | Powertrain Control Module (PCM) Internal IMA-CAN Communication Circuit Malfunction | ||||||||||
| P1860 (33)(2) | - | Blinks | OFF | Inhibitor Solenoid Circuit Low Voltage | ||||||||||
| P1861 (33)(2) | - | Blinks | OFF | Inhibitor Solenoid Circuit High Voltage | ||||||||||
| P1890 (42) | - | Blinks | OFF | Problem in CVT Speed Control System | ||||||||||
| P1891 (43) | - | Blinks | OFF | Problem in Start Clutch Control System | ||||||||||
| P1898 (100)/P0780 (100) | ◦ | Blinks | ON | CVT Drive Pulley Pressure Control Valve Stuck ON or CVT Driven Pulley Pressure Control Valve Stuck OFF | ||||||||||
| P1899 (100)/P0780 (100) | ◦ | Blinks | ON | CVT Drive Pulley Pressure Control Valve Stuck OFF or CVT Driven Pulley Pressure Control Valve Stuck ON | ||||||||||
| P2122 (20) | - | Blinks | ON | Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP) Sensor D) Circuit Low Voltage Input | ||||||||||
| P2123 (20) | - | Blinks | ON | Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP) Sensor D) Circuit High Voltage Input | ||||||||||
| U0029 (107)(4) | - | OFF | OFF or ON(3) | F-CAN Malfunction (BUS-OFF) | ||||||||||
| U0029 (107) | - | OFF | OFF or ON(3) | F-CAN Malfunction (BUS-OFF) | ||||||||||
| U0038 (120)(4) | - | Blinks | ON | IMA-CAN Malfunction (BUS-OFF) | ||||||||||
| U0038 (120)(5) | - | Blinks | ON | IMA-CAN Malfunction (BUS-OFF) | ||||||||||
| U0121 (107)(4) | - | Blinks | OFF | F-CAN Malfunction (Powertrain Control Module (PCM)-ABS) | ||||||||||
| U0122 (107)(4) | - | Blinks | OFF | F-CAN Malfunction (Powertrain Control Module (PCM)-VSA) | ||||||||||
| U0122 (107)(5) | - | Blinks | OFF | F-CAN Malfunction (Powertrain Control Module (PCM)-VSA) | ||||||||||
| U0155 (107)(3)(4) | - | OFF | OFF or ON(3) | F-CAN Malfunction (Powertrain Control Module (PCM)-Gauge Control Module) | ||||||||||
| U0155 (107)(3) | - | OFF | OFF or ON(3) | F-CAN Malfunction (Powertrain Control Module (PCM)-Gauge Control Module) | ||||||||||
| U0301 (129)(4) | - | Blinks | ON | PGM-FI System and A/T System Program Version Mismatch | ||||||||||
| U0302 (129)(5) | - | Blinks | ON | PGM-FI System and A/T System Program Version Mismatch | ||||||||||
| U1205 (120)(4) | - | Blinks | ON | IMA-CAN Malfunction (Powertrain Control Module (PCM)-Motor Control Module (MCM)) | ||||||||||
| U1205 (120)(5) | - | Blinks | ON | IMA-CAN Malfunction (Powertrain Control Module (PCM)-Motor Control Module (MCM)) | ||||||||||
|
||||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
