Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Honda Element SC, AutomaticFACTORY OEM SERVICE PROCEDURE
Fuel And Emissions Systems
- Special Tools
- General Troubleshooting Information
- Intermittent Failures
- Opens and Shorts
- How to Use the HDS (Honda Diagnostic System)
- HDS Clear Command
- Scan Tool Clear Command
- DTC Clear
- ECM/PCM Reset
- Crank (CKP) Pattern Clear/Crank (CKP) Pattern Learn
- How to Troubleshoot Circuits at the ECM/PCM Connectors
- Updating the ECM/PCM
- Substituting the ECM/PCM
- OBD Status
- DTC Troubleshooting Index
- Symptom Troubleshooting Index
- System Description
- Electronic Control System
- Vacuum Hose Routing
- Vacuum Distribution
- ECM/PCM Inputs and Outputs at Connector A (31P)
- ECM/PCM Inputs and Outputs at Connector B (24P)
- ECM/PCM Inputs and Outputs at Connector C (22P)
- ECM/PCM Inputs and Outputs at Connector D (17P)
- ECM/PCM Inputs and Outputs at Connector E (31P)
- PGM-FI System
- Notes
- Air Conditioning (A/C) Compressor Clutch Relay
- Air Fuel Ratio (A/F) Sensor
- Barometric Pressure (BARO) Sensor
- Camshaft Position (CMP) Sensor B
- Crankshaft Position (CKP) Sensor
- Engine Coolant Temperature (ECT) Sensors 1 and 2
- Ignition Timing Control
- Injector Timing and Duration
- Knock Sensor
- Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)
- Manifold Absolute Pressure (MAP) Sensor
- Mass Air Flow (MAF) Sensor/Intake Air Temperature (IAT) Sensor
- Output Shaft (Countershaft) Speed Sensor
- Secondary Heated Oxygen Sensor (Secondary HO2S)
- Electronic Throttle Control System
- i-VTEC
- VTEC/VTC
- Idle Control System
- Fuel Supply System
- Intake Air System
- Catalytic Converter System
- Evaporative Emission (EVAP) Control System
- Fuel Cap Warning Message
- To Make the Message Go Off (With the HDS)
- To Make the Message Go Off (Without the HDS)
- Electronic Throttle Control System Diagram
- Evaporative Emission (EVAP) Control Diagram
- How to Set Readiness Codes
- Malfunction Indicator Lamp (MIL) Indication (In Relation To Readiness Codes)
- Catalytic Converter Monitor and Readiness Code
- Evaporative Emission (EVAP) Control System Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Heater Monitor Readiness Code
- Misfire Monitor and Readiness Code
- Fuel System Monitor and Readiness Code
- Comprehensive Component Monitor and Readiness Code
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.