Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Honda Pilot EXFACTORY OEM SERVICE PROCEDURE
PCM Inputs and Outputs
PCM CONNECTOR A (SQUARE) (44P)Β
PCM CONNECTOR A (SQUARE) (44P) TERMINAL NUMBER DESCRIPTION
| Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
|---|---|---|---|---|
| A1 | RED | CANL | CAN communication signal low | With ignition switch ON (II): Pulsing signal |
| A2 | WHT/RED | SLS | Shift lock solenoid control | With ignition switch ON (II), in the P position, brakepedal pressed, and accelerator released: Battery voltage |
| A8 | WHT/BLK | BK SW | Brake pedal position switch signal input | Brake pedal pressed: Battery voltage Brake pedal released: 0 V |
| A12 | BLU/BLK | ATP P | Transmission range switch P position signal input | In the P position: 0 V In other than P position: Battery voltage |
| A31 | BRN | SCS | Detects service check signal | With the SCS shorted with the HDS: About 0 V With the SCS open: About 5 V |
| A36 | WHT | CANH | CAN communication signal high | With ignition switch ON (II): Pulsing signal |
| A43 | GRY | K-LINE | Communication line PCM-to-DLC | With ignition switch ON (II): Battery voltage |
| PCM CONNECTOR B (TRIANGLE) (44P)Β | ||||
| B1 | BLK | PG2 | Ground | Less than 1.0 V at all times |
| B2 | BLK/YEL | VB SOL | Source for solenoid valves | With ignition switch ON (II): Battery voltage With ignition switch OFF: 0 V |
| B3 | YEL/BLK | IGP | Power source for PCM circuit | With ignition switch ON (II): Battery voltage |
| B18 | YEL/RED | VCC1 | Provides sensor voltage | With ignition switch ON (II): 5 V With ignition switch OFF: 0 V |
| B25 | BRN/WHT | LS B | A/T clutch pressure control solenoid valve B control | With ignition switch ON (II): Pulsing signal |
| B33 | GRN/WHT | SG1 | Sensor ground | Less than 1.0 V at all times |
| B35 | GRN/RED | LS C | A/T clutch pressure control solenoid valve C control | With ignition switch ON (II): Pulsing signal |
| B36 | BLK | PG1 | Ground | Less than 1.0 V at all times |
| B39 | RED | NM | Input shaft (mainshaft) speed sensor signal input | With ignition switch ON (II): 0 V or about 5 V With engine at idling in the N position: About 2.5 V |
| B40 | BLU | NC | Output shaft (countershaft) speed sensor signal input | With ignition switch ON (II): 0 V or about 5 V With driving: About 2.5 V |
| B43 | BRN/YEL | LG2 | Ground | Less than 1.0 V at all times |
| B44 | YEL | LC | Torque converter clutch solenoid valve control | During lock-up condition: Battery voltage During no lock-up condition: 0 V |
| PCM CONNECTOR C (CIRCLE) (44P)Β | ||||
| C13 | YEL/BLU | VCC2 | Provides sensor voltage | With ignition switch ON (II): 5 V With ignition switch OFF: 0 V |
| C14 | GRN/YEL | SG2 | Sensor ground | Less than 1.0 V at all times |
| C15 | BLU/WHT | OP3SW | 3rd clutch transmission fluid pressure switch signal input | With ignition switch ON (II): Without 3rd clutch pressure: About 5 V With 3rd clutch pressure: About 0 V |
| C16 | BLU/YEL | OP4SW | 4th clutch transmission fluid pressure switch signal input | With ignition switch ON (II): Without 4th clutch pressure: About 5 V With 4th clutch pressure: About 0 V |
| C17 | BLU/YEL | ATP FWD | Transmission range switch D, D3, and 2 position signal input | In the D, D3, and 2 position: 0 V In other than the D, D3, and 2 position: Battery voltage |
| C18 | GRN | SH C | Shift solenoid valve C control | Battery voltage in these positions:
0 V in these positions:
|
| C19 | RED | LS A | A/T clutch pressure control solenoid valve A control | With ignition switch ON (II): Pulsing signal |
| PCM CONNECTOR C (CIRCLE) (44P)Β | ||||
| C23 | GRN/WHT | SH B | Shift solenoid valve B control | Battery voltage in these positions:
0 V in these positions:
|
| C25 | BLU/YEL | SH A | Shift solenoid valve A control | Battery voltage in these positions:
0 V in these positions:
|
| C28 | BLU/YEL | ATFT | ATF temperature sensor signal input | With ignition switch ON (II): 0.1-4.2 V (Depending on ATF temperature) With ignition switch OFF: 0 V |
| C30 | WHT | ATP R | Transmission range switch R position signal input | In the R position: 0 V In other than the R position: Battery voltage |
| C31 | RED/BLK | ATP N | Transmission range switch N position signal input | In the N position: 0 V In other than the N position: Battery voltage |
| C32 | YEL | ATP D | Transmission range switch D position signal input | In the D position: 0 V In other than the D position: Battery voltage |
| C33 | RED | ATP D3 | Transmission range switch D3 position signal input | In the D3 position: 0 V In other than the D3 position: Battery voltage |
| C34 | BLU | ATP 2 | Transmission range switch 2 position signal input | In the 2 position: 0 V In other than the 2 position: Battery voltage |
| C35 | BRN | ATP 1 | Transmission range switch 1 position signal input | In the 1 position: 0 V In other than the 1 position: Battery voltage |
| C40 | BRN/YEL | LG1 | Ground | Less than 1.0 V at all times |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
