2005 Honda Civic SiFACTORY OEM SERVICE PROCEDURE

Wheel Alignment Specifications: Specifications

Wheel Alignment Specifications (Hybrid)

Item Measurement Qualification Standard or New Service Limit
Wheel alingment Camber Front -0° 12' ± 45'
Rear -1° 00 ' ± 45 '
Caster Front (ULEV model) 2 ° 20 ' ± 1 °
Front [AT-PZEV (SULEV) model] 2°10' ±1°
Total Toe-in Front 0±3 mm (0±1/8 in.)
Rear 2+2-1 mm (1/16+1/16-1/32 in.)
Front wheel turning angle Inside wheel 39 ° 00 ' ± 2 °
Outside wheel 31 ° 00 ' (Reference)
Wheel Alignment Specifications (With CNG)

Item Measurement Qualification Standard or New Service Limit
Wheel alignment Camber Front 0 ° 00 ' ± 45 °
Rear -0 ° 45 ' ± 45 '
Caster Front 1 ° 33 ' ±1 °
Total Toe-in Front 0±3 mm (0± 0.12 in.)
Rear 2+2-1 mm (0.08+0 08-0.04 in.)
Front wheel turning angle Inside wheel 40 ° 00 ' ± 2 °
Outside wheel 31 ° 00 ' (Reference)
Wheel Alignment Specifications (Without CNG)

Item Measurement Qualification Standard or New Service Limit
Wheel alignment Camber Front 0°00' ± 45'
Rear -0°45' ± 45'
Caster Front 2001-2002 models: 1°33' ± 1°
2003-2005 models: 2°14' ± 1°
Total Toe-in Front 0 ± 3 mm (0 ± 0.12 in.)
Rear 2+2-1 mm (0.08+0.08-0.04 in.)
Front wheel turning angle Inside wheel Without P195/60R15 87H tire: 40°00' ± 2°
With P195/60R15 87H tire: 38°00' ± 2°
Outside wheel Without P195/60R15 87H tire: 31°00' (Reference)
With P195/60R15 87H tire: 30°00' (Reference)
Wheel Alignment Specifications (3-Door)

Item Measurement Qualification Standard or New Service Limit
Wheel alignment Camber Front(2002-2003 models) 0 ° 00 ' ± 45 '
Front (2004-2005 models) -0 ° 09 ' ± 45 '
Rear (2002-2003 models) -0 ° 45 ' ± 45 '
Rear (2004-2005 models) -0 ° 51 ' ± 45 '
Caster Front (2002-2003 models) 1 ° 03 ' ±1 °
Front (2004-2005 models) 1 ° 36 ' ±1 °
Total Toe-in Front 0±3 mm (0± 0.12 in.)
Rear 2+2-1 mm (0.08+0.08-0.04 in.)
Front wheel turning angle Inside wheel (2002-2003 models) 37° 40' ± 2°
Inside wheel (2004-2005 models) 34° 40' ± 2°
Outside wheel (2002-2003 models) 29 ° 50' (Reference)
Outside wheel (2004-2005 models) 28° 10 '(Reference)
Chapter Navigation
Return to Chapter: Wheel Alignment Specifications
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.