Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Honda Prelude Base, StandardFACTORY OEM SERVICE PROCEDURE
Engine Performance DTCS
ENGINE PERFORMANCE DIAGNOSTIC TROUBLE CODES (DTC) LIST
| DTC (MIL/"D4" Code) | Description |
|---|---|
| P0107 (3) | MAP Sensor Circuit Low Voltage Input |
| P0108 (3) | MAP Sensor Circuit High Voltage Input |
| P0112 (10) | IAT Sensor Circuit Low Voltage Input |
| P0113 (10) | IAT Sensor Circuit High Voltage Input |
| P0116 (86) | ECT Sensor Circuit Range/Performance Problem |
| P0117 (6) | ECT Sensor Circuit Low Voltage Input |
| P0118 (6) | ECT Sensor Circuit High Voltage Input |
| P0122 (7) | Throttle Position Sensor Circuit Low Voltage Input |
| P0123 (7) | Throttle Position Sensor Circuit High Voltage Input |
| P0131 (1) | Primary HO2S-1 Low Voltage Input |
| P0132 (1) | Primary HO2S-1 High Voltage Input |
| P0133 (61) | Primary HO2S-1 Slow Response |
| P0135 (41) | Primary HO2S-1 Heater Circuit Malfunction |
| P0137 (63) | Secondary HO2S-2 Low Voltage Input |
| P0138 (63) | Secondary HO2S-2 High Voltage Input |
| P0139 (63) | Secondary HO2S-2 Slow Response |
| P0141 (65) | Secondary HO2S-2 Heater Circuit Malfunction |
| P0171 (45) | System Too Lean |
| P0172 (45) | System Too Rich |
| P0300 (71-74) | Random Misfire Detected |
| P0301 (71) | Cylinder No. 1 Misfire Detected |
| P0302 (72) | Cylinder No. 2 Misfire Detected |
| P0303 (73) | Cylinder No. 3 Misfire Detected |
| P0304 (74) | Cylinder No. 4 Misfire Detected |
| P0325 (23) | Knock Sensor (KS) Circuit Malfunction |
| P0335 (4) | CKP Sensor Circuit Malfunction |
| P0336 (4) | CKP Sensor Circuit Range/Performance Problem |
| P0401 (80) | EGR Insufficient Flow Detected |
| P0420 (67) | Catalyst System Efficiency Below Threshold |
| P0451 (91) | Fuel Tank Pressure Sensor Circuit Range/Performance Problem |
| P0452 (91) | Fuel Tank Pressure Sensor Circuit Low Voltage Input |
| P0453 (91) | Fuel Tank Pressure Sensor Circuit High Voltage Input |
| P0500 (17) | Vehicle Speed Sensor (VSS) Circuit Malfunction |
| P0505 (14) | Idle Control System Malfunction |
| P1106 (13) | BARO Sensor Circuit Range/Performance Problem |
| P1107 (13) | BARO Sensor Circuit Low Voltage Input |
| P1108 (13) | BARO Sensor Circuit High Voltage Input |
| P1121 (7) | Throttle Position Lower Than Expected |
| P1122 (7) | Throttle Position Higher Than Expected |
| P1128 (5) | Manifold Absolute Pressure Lower Than Expected |
| P1129 (5) | Manifold Absolute Pressure Higher Than Expected |
| P1259 (22) | VTEC System Malfunction |
| P1297 (20) | Electrical Load Detector Circuit Low Voltage Input |
| P1298 (20) | Electrical Load Detector Circuit High Voltage Input |
| P1359 (8) | CKP/TDC Sensor Connector Poor Connection |
| P1361 (8) | TDC Sensor Circuit Intermittent Interruption |
| P1362 (8) | TDC Sensor Circuit No Signal |
| P1381 (9) | CYP Sensor Circuit Intermittent Interruption |
| P1382 (9) | CYP Sensor Circuit No Signal |
| P1456 (90) | EVAP System Leak Detected (Fuel Tank System) |
| P1457 (90) | EVAP System Leak Detected (Canister System) |
| P1491 (12) | EGR Valve Insufficient Lift Detected |
| P1498 (12) | EGR Valve Lift Sensor Circuit High Voltage Input |
| P1508 (14) | Idle Air Control (IAC) Valve Circuit Failure |
| P1607 (-) | PCM Internal Failure "A" |
| P1655 (30) | SEAF/SEFA Signal Circuit Failure |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
