Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1997 Honda CR-V SDMAFACTORY OEM SERVICE PROCEDURE
External Pages
These are pages that do not belong to the exact selected vehicle (1997 Honda CR-V SDMA), but are still accessible from a link in your vehicle's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle.
- Different car
- Section 1 (Removal & Installation - A/T)
- Section 2 (Engine Controls - Self-Diagnostics)
- Section 3 (Engine Controls - Self-Diagnostics)
- Section 4 (Engine Controls - Service & Adjustments Specifications)
- Section 5 (Engine Controls - On-Vehicle Adjustments)
- Section 6 (Engine Controls - Basic Diagnostic Procedures)
- Section 7 (Engine Controls - Self-Diagnostics - Introduction)
- Section 8 (Engine Controls - Self-Diagnostics - 2.2L)
- Section 9 (Engine Controls - Self-Diagnostics - 2.2L)
- Section 10 (Engine Controls - Self-Diagnostics - 3.2L & 3.5L)
- Section 11 (Engine Controls - Self-Diagnostics - 4.3L)
- Section 12 (Engine Controls - Trouble Shooting - No Codes)
- Section 13 (Engine Controls - System & Component Testing)
- Section 14 (Vacuum Diagrams)
- Section 15 (Engine Controls - Removal, Overhaul & Installation)
- Section 16 (Engine Controls - Pin Voltage Charts)
- Section 17 (Engine Controls - Service & Adjustment Specifications)
- Section 18 (Engine Controls - On-Vehicle Adjustments)
- Section 19 (Engine Controls - Basic Diagnostic Procedures)
- Section 20 (Engine Controls Self-Diagnostics - Introduction)
- Section 21 (Engine Control System & Engine Component Tests)
- Section 22 (Vacuum Diagrams)
- Section 23 (Engine Controls - Removal & Installation & Overhaul)
- Section 24 (Engine Performance Wiring Diagrams)
- Section 25 (Engine Controls - Tests W/O Codes)
- Section 26 (Engine Controls - Pin Voltage Charts)
- Section 27 (Disc & Drum)
- Section 28 (Wheel Alignment Specifications & Adjustment Procedures)
- Section 29 (Front Suspension System)
- Section 30 (Rear Suspension System)
- Section 31 (Disc & Drum)
- Section 32 (Specifications & Procedures)
- Section 33 (Front Suspension)
- Section 34 (Disc & Drum)
- Section 35 (Disc Brakes)
- Section 36 (Engine - 2.0L)
- Section 37 (Engine Cooling System Specifications And Drive Belt Routing)
- Section 38 (Engine Controls - Service & Adjustment Specifications)
- Section 39 (Generators & Regulators)
- Section 40 (Starting System)
- Section 41 (Manual HVAC System - System)
- Section 42 (Disc Brakes & Drum Brakes)
- Section 43 (Wheel Alignment Specifications & Adjustment Procedures)
- Section 44 (System Wiring Diagrams)
- Section 45 (System Wiring Diagrams)
- Section 46 (System Wiring Diagrams)
- Section 47 (Battery)
- Section 48 (Firing Order & Cylinder Identification)
- Section 49 (EGR Function Testing - HONDA)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
