Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1996 Geo Metro Base, 2D Hatchback, 1.3 9FACTORY OEM SERVICE PROCEDURE
Scan Tool Data
NOTE:
Information contained in the following tables is typical of readings taken on a vehicle with engine idling at normal operating temperature, throttle closed, transmission in Park or Neutral, system in closed loop status, and all accessories off (except as noted in tables). For additional information, see scan tool owner's manual.
SCAN TOOL DATA VALUES
| Scan Tool Parameters | Typical Data Value | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ECT | (1) 185-203°F (85-95°C) | ||||||||||||||||||
| IAT | (2) 80°F (10°C) | ||||||||||||||||||
| Desired Idle Speed | 850 RPM | ||||||||||||||||||
| Closed Throttle Switch | ON | ||||||||||||||||||
| IAC Flow Duty | 20-40% | ||||||||||||||||||
| Engine Speed | (3) | ||||||||||||||||||
| Short Term FT | -20 - +20% | ||||||||||||||||||
| Long Term FT | -15 - +15% | ||||||||||||||||||
| Spark | -1° - -18° | ||||||||||||||||||
| Battery+ Voltage | 10-14 Volts | ||||||||||||||||||
| MAF | Not Available | ||||||||||||||||||
| Fuel Inj. PWM | 0.8-2.3 mS | ||||||||||||||||||
| Throttle Position Angle | 7-18% | ||||||||||||||||||
| Throttle Position Sensor | .42-1.15 Volts | ||||||||||||||||||
| HO2S1 | (4) 50-950mV | ||||||||||||||||||
| HO2S2 | (4) 0-950mV | ||||||||||||||||||
| Loop Status | Closed | ||||||||||||||||||
| Engine Load | 3-5% | ||||||||||||||||||
| Total Fuel Trim | -35 - +35% | ||||||||||||||||||
| Fuel Cut Signal | OFF | ||||||||||||||||||
| EVAP Purge Flow Duty | 0-100% | ||||||||||||||||||
| Fuel Tank Pressure | (5) 0 kPa (0 mm Hg) | ||||||||||||||||||
| EGR Solenoid Vacuum Valve | OFF | ||||||||||||||||||
| EGR Bypass Solenoid | OFF | ||||||||||||||||||
| MAP | (6) 29-47 kPa/1.32 (1.90 Volts) | ||||||||||||||||||
| Vehicle Speed | 0 MPH (0 KM/H) | ||||||||||||||||||
| Electrical Load Signal | (7) OFF | ||||||||||||||||||
| Engine Cooling Fan | (1) ON/OFF | ||||||||||||||||||
| Power Steering Switch | (8) ON/OFF | ||||||||||||||||||
| Air Conditioning | OFF | ||||||||||||||||||
| EVAP Canister Purge Solenoid | (9) ON/OFF | ||||||||||||||||||
| Fuel Tank Pressure Solenoid | (4) ON/OFF | ||||||||||||||||||
| Fuel Tank Level | Varies | ||||||||||||||||||
| Gear Position | "P" Or "N", "D", "2", "1" | ||||||||||||||||||
|
|||||||||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
