Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1990 Geo Metro L3-61 1.0LFACTORY OEM SERVICE PROCEDURE
Computers and Control Systems: Adjustments
IDLE SPEED CHECK AND ADJUSTMENT
NOTE: Before starting engine place transaxle gear selector in Park (Neutral for M/T) and set parking brake and block drive wheels.

1. Check accelerator cable for free movement and excessive play, cable play should be within specification.
2. Inspect lead wires and hoses of EFI and engine emissions control systems for secure connections.
3. Check ignition timing and adjust if necessary.
4. Turn "OFF" all accessories (A/C, wipers, heater, lights, etc.).
5. Make sure air cleaner is installed correctly.
6. Remove cover on idle speed adjusting screw.
7. Start engine and allow it to reach normal operating temperature (all accessories "OFF")
8. Connect a tachometer.

9. Install a spare fuse to diagnosis switch terminal in fuse block.
10. Check idle speed, it should be:
A/T Metro LSI 700 +/- 50 rpm
A/T 850 +/- 50 rpm
M/T 750 +/- 50 rpm

11. If necessary, adjust idle speed by turning idle speed adjusting screw "IN" to increase or "OUT" to decrease idle speed.
12. Remove spare fuse from diagnosis switch terminal, disconnect tachometer and install idle speed screw cover.
A/C VSV ADJUSTMENT [A/C idle up solenoid]

1. Start engine and allow it to reach normal operating temperature (with A/C "ON").
2. Connect a tachometer.
3. Install a spare fuse in diagnosis switch terminal.

3. Check idle speed, adjust as necessary using the A/C vacuum switch idle screw. Idle should be:
A/T 850 +/- 50 rpm
M/T 900 +/- 50 rpm
4. Remove spare fuse from diagnosis switch terminal and disconnect tachometer from engine.
NOTE: Before starting engine place transaxle gear selector in Park (Neutral for M/T) and set parking brake and block drive wheels.
Accelerator Cable Adjustment:
1. Check accelerator cable for free movement and excessive play, cable play should be within specification.
2. Inspect lead wires and hoses of EFI and engine emissions control systems for secure connections.
3. Check ignition timing and adjust if necessary.
4. Turn "OFF" all accessories (A/C, wipers, heater, lights, etc.).
5. Make sure air cleaner is installed correctly.
6. Remove cover on idle speed adjusting screw.
7. Start engine and allow it to reach normal operating temperature (all accessories "OFF")
8. Connect a tachometer.
Diagnosis Switch Terminal:
9. Install a spare fuse to diagnosis switch terminal in fuse block.
10. Check idle speed, it should be:
A/T Metro LSI 700 +/- 50 rpm
A/T 850 +/- 50 rpm
M/T 750 +/- 50 rpm
Idle Speed Adjusting Screw:
11. If necessary, adjust idle speed by turning idle speed adjusting screw "IN" to increase or "OUT" to decrease idle speed.
12. Remove spare fuse from diagnosis switch terminal, disconnect tachometer and install idle speed screw cover.
A/C VSV ADJUSTMENT [A/C idle up solenoid]
VSV Component Location:
1. Start engine and allow it to reach normal operating temperature (with A/C "ON").
2. Connect a tachometer.
3. Install a spare fuse in diagnosis switch terminal.
Adjusting Screw For A/C VSV:
3. Check idle speed, adjust as necessary using the A/C vacuum switch idle screw. Idle should be:
A/T 850 +/- 50 rpm
M/T 900 +/- 50 rpm
4. Remove spare fuse from diagnosis switch terminal and disconnect tachometer from engine.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
