Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Genesis Electrified G80 AdvancedFACTORY OEM SERVICE PROCEDURE
Front Radar DTCS
FRONT RADAR DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| B1698-87 | CAN Time-Out SWRC |
| C1101-17 | Battery Voltage High |
| C1102-16 | Battery Voltage Low |
| C1202-81 | Wheel Speed Sensor Front-LH Invalid/No Signal |
| C1205-81 | Wheel Speed Sensor Front-RH Invalid/No Signal |
| C1208-81 | Wheel Speed Sensor Rear-LH Invalid/No Signal |
| C1211-81 | Wheel Speed Sensor Rear-RH Invalid/No Signal |
| C1360-81 | ESP Irreversible Error |
| C1604-04 | ECU Hardware Error |
| C160A-88 | Local CAN Bus OFF |
| C160C-87 | Local CAN Time-Out |
| C1614-87 | CAN Time-Out HCU/VCC/FCU |
| C161E-88 | E-CAN Bus OFF |
| C1620-78 | Alignment Failed |
| C1623-87 | CAN Time-Out Steering Angle Sensor |
| C1625-87 | CAN Time-Out ABS/ESP |
| C1628-87 | CAN Time-Out Cluster |
| C1638-81 | ACC/SCC Communication Error |
| C1642-81 | CAN Message Failure - Brake (Invalid) |
| C1642-82 | CAN Message Failure - Brake (Alive counter) |
| C1642-83 | CAN Message Failure - Brake (CRC) |
| C1656-81 | CAN Signal Error - Cluster (Invalid) |
| C1656-82 | CAN Signal Error - Cluster (Alive Counter) |
| C1656-83 | CAN Signal Error - Cluster (CRC) |
| C165C-87 | CAN Time-Out YRS |
| C1672-81 | SAS Message Counter Error (Invalid) |
| C1672-82 | SAS Message Counter Error (Alive Counter) |
| C1672-83 | SAS Message Counter Error (CRC) |
| C16B8-81 | AEB Communication Error |
| C1702-55 | Variant Coding Error |
| C1741-81 | Esc-Not Available VSM (Check ESC) |
| C1742-81 | Variant Error - ESC (Check ESC) |
| C1744-55 | SCC Coding & AVN/Navi Option Mismatch |
| C1747-55 | Front Radar & Front View Camera Variant Coding Mismatch |
| C1804-87 | CAN Time-Out LKAS |
| C1805-81 | LKAS CAN Signal Error (Invalid) |
| C1805-82 | LKAS CAN Signal Error (Alive counter) |
| C1805-83 | LKAS CAN Signal Error (CRC) |
| C1812-87 | CAN Time-Out Gateway |
| C183D-82 | CAN Message Failure - SWRC (Alive Counter) |
| C183D-83 | CAN Message Failure - SWRC (CRC) |
| C1842-81 | Invalid Signal Of YRS (Invalid) |
| C1842-82 | Invalid Signal Of YRS (Alive Counter) |
| C1842-83 | Invalid Signal Of YRS (CRC) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.