Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2023 Genesis Electrified GV70 AdvancedFACTORY OEM SERVICE PROCEDURE
Front View Camera DTCS
FRONT VIEW CAMERA DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| C1101-17 | Battery Voltage High |
| C1102-16 | Battery Voltage Low |
| C135F-81 | HCU/VCU/FCU Torque Control Unavailable for SCC |
| C1532-11 | Lane Safety Button Failure |
| C1532-15 | Lane Safety Button Failure |
| C1532-23 | Lane Safety Button Failure |
| C1604-49 | ECU Hardware Error |
| C1606-49 | ECU Software Error |
| C160A-87 | Local CAN Bus OFF |
| C160A-88 | Local CAN Bus OFF |
| C160C-87 | Local CAN Time-Out |
| C1614-87 | CAN Time-Out HCU/VCU/FCU |
| C161C-86 | CAN Signal Error HCU/VCU/FCU |
| C161E-87 | E-CAN Bus OFF (E-CAN Bus Off Error) |
| C1623-85 | CAN Time-out Steering Angle Sensor |
| C1623-87 | CAN Time-out Steering Angle Sensor |
| C1625-85 | CAN Time-Out ABS/ESP |
| C1625-87 | CAN Time-Out ABS/ESP |
| C1628-87 | CAN Time-out Cluster |
| C1642-86 | CAN Message Failure - Brake |
| C1656-86 | CAN Signal Error - Cluster |
| C165C-87 | CAN Time-out YRS |
| C1669-87 | CAN Time-Out ACU |
| C1672-86 | SAS Message Counter Error |
| C167A-87 | CAN Time-Out NAVI |
| C1687-85 | CAN Time-Out VSM2 (MDPS) |
| C1687-87 | CAN Time-Out VSM2 (MDPS) |
| C1688-86 | VSM2 (MDPS) Signal Error |
| C16B9-02 | FCA, SCC Communication Error |
| C1702-46 | Variant Coding Error |
| C1742-81 | Variant Error - ESC (Check ESC) |
| C1746-86 | HDA Coding & AVN/Navi Option Mismatch |
| C1812-87 | CAN Time-out Gateway |
| C1842-86 | YRS_YawRate or YRS_LatAccel or YRS LongAccel Not valid |
| C1850-87 | CAN Time-Out MFSW |
| C186A-87 | CAN Time-Out ILCU LH |
| C186B-87 | CAN Time-Out ILCU RH |
| C2239-86 | MDPS Steering Control Failure for LKA |
| C2253-87 | CAN Time-Out IBU |
| C2721-46 | System Calibration Required |
| C2722-46 | System Out of Calibration |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.