Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2022 Genesis GV70 2.5TFACTORY OEM SERVICE PROCEDURE
Front View Camera DTCS
FRONT VIEW CAMERA DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| C1101-17 | Battery Voltage High |
| C1102-16 | Battery Voltage Low |
| C1604-49 | ECU Hardware Error |
| C1606-49 | ECU Software Error |
| C160A-87 | Local CAN Bus Off |
| C160C-87 | Local CAN Time-Out |
| C1611-87 | CAN Time-out EMS |
| C1612-87 | CAN Time-out TCU |
| C1613-86 | CAN Signal Error EMS |
| C161E-87 | E-CAN FD Bus off |
| C1623-85 | CAN Time-out Steering Angle Sensor |
| C1623-87 | CAN Time-out Steering Angle Sensor |
| C1625-85 | CAN Time-Out ABS/ESP |
| C1625-87 | CAN Time-Out ABS/ESP |
| C1628-87 | CAN Time-out Cluster |
| C1642-86 | CAN Signal Error - ABS/ESP |
| C1646-86 | CAN Signal Error - TCU |
| C1656-86 | CAN Signal Error - Cluster |
| C165C-87 | CAN Time-out YRS |
| C1667-87 | CAN Time-out SCC |
| C1672-86 | CAN Signal Error - Steering Angle Sensor |
| C1687-85 | CAN Time-out MDPS |
| C1687-87 | CAN Time-out MDPS |
| C1688-86 | CAN Signal Error - MDPS |
| C16B6-87 | CAN Time-Out FCA |
| C16B8-02 | CAN Signal Error - AEB |
| C1702-46 | Variant Coding Error |
| C1702-62 | Variant Coding Error |
| C1746-86 | HDA Coding & AVN/Navi Option Mismatch |
| C1812-87 | CAN Time-out Gateway |
| C1831-86 | CAN Signal Error - Navigation |
| C1842-86 | YRS_YawRate or YRS_LatAccel or YRS LongAccel Not valid |
| C1849-87 | CAN Time-Out H_U |
| C1850-87 | CAN Time-Out MFSW |
| C1862-86 | CAN Signal Error - SCC |
| C1863-87 | CAN Time-out NAVI for HDA |
| C186A-87 | CAN Time-Out ILCU LH |
| C186B-87 | CAN Time-Out ILCU RH |
| C2239-86 | MDPS Steering Control Failure for LKAS |
| C2253-87 | CAN Time-Out IBU |
| C2721-46 | System Calibration Required |
| C2722-46 | System Out of Calibration |
| C28AB-87 | CAN Time-Out FR_RDR |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.