Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Genesis G70 2.0T Elite, AWDFACTORY OEM SERVICE PROCEDURE
Front View Camera DTCS
FRONT VIEW CAMERA DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| DTC C1101 | 17: Battery Voltage High |
| DTC C1102 | 16: Battery Voltage Low |
| DTC C1532 | 11: LKAS Switch Failure |
| DTC C1532 | 12: LKAS Switch Failure |
| DTC C1532 | 86: LKAS Switch Failure |
| DTC C153A | 11: LKAS Switch Indicator Failure |
| DTC C1604 | 49: ECU Hardware Error |
| DTC C1606 | 49: ECU Software Error |
| DTC C160A | 87: Local CAN bus off |
| DTC C1611 | 87: CAN timeout of EMS |
| DTC C1612 | 87: CAN timeout of TCU |
| DTC C1613 | 86: Invalid signal of EMS |
| DTC C1616 | 88: CAN Bus OFF |
| DTC C1623 | 85: CAN Timeout of SAS (Time-Delta) |
| DTC C1623 | 87: CAN Timeout of SAS (Missing) |
| DTC C1625 | 85: CAN Timeout of ABS/ESP (Time-Delta) |
| DTC C1625 | 87: CAN Timeout of ABS/ESP (Missing) |
| DTC C1628 | 87: CAN Timeout of CLU |
| DTC C1642 | 86: Invalid Signal of ABS/ESP |
| DTC C1646 | 86: Invalid signal of TCU |
| DTC C1656 | 86: Invalid Signal of CLU |
| DTC C1667 | 87: CAN Timeout of SCC |
| DTC C1672 | 86: Invalid Signal of SAS |
| DTC C1687 | 85: CAN Timeout of MDPS (Time-Delta) |
| DTC C1687 | 87: CAN Timeout of MDPS (Missing) |
| DTC C1688 | 86: Invalid Signal of MDPS |
| DTC C16B6 | 87: CAN timeout of AEB |
| DTC C1702 | 46: Variant coding required |
| DTC C1702 | 62: Variant coding required |
| DTC C1746 | 86: HDA Coding & Navi Mismatch |
| DTC C1812 | 87: CAN Timeout of CGW |
| DTC C1816 | 86: Invalid Signal of CGW |
| DTC C1831 | 86: Invalid Signal of NAVI |
| DTC C1862 | 86: Invalid Signal of SCC |
| DTC C1863 | 87: CAN Timeout of NAVI for HDA |
| DTC C2223 | 86: MDPS Steering Control Failure |
| DTC C2721 | 46: System Calibration Required |
| DTC C2722 | 46: System Out of Calibration |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.