2019 Genesis G70 2.0T Advanced, AWDFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

NOTE:
  • When DTC for solenoid valve is ON, replace according to the following procedure:
  • Automatic transmission is composed of fine components. Use special caution when assembling/disassembling to avoid any damage of the component.
  • Maintain clean condition so that foreign substance does not get into the automatic transmission.
  • Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transmission.
  • ATF is reusable. Store it in a clean 10 liter beaker.
  1. Remove the under cover.

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ")

  2. Remove the ATF drain plug (A) and then allow the fluid to drain out and then reinstall the drain plug.

    Tightening torque  :

    22.6 - 24.5 N.m (2.3 - 2.5 kgf.m, 16.6 - 18.1 lb-ft)

    G13540094Courtesy of HYUNDAI MOTOR AMERICA
    NOTE:
    • ATF can be reused. Collect it in a clean beaker.
    • The existing ATF drain plug o-ring must be replaced with a new one. (Do not reuse it.)
      G13540095Courtesy of HYUNDAI MOTOR AMERICA
  3. Disconnect the E-module connector (A).
    G13540096Courtesy of HYUNDAI MOTOR AMERICA
  4. Remove the valve body cover.
    1. Loosen the all valve body mounting bolts except for the bolts (A) in the corner.

      Tightening torque  :

      13.7 - 15.7 N.m (1.4 - 1.6 kgf.m, 10.1 - 11.6 lb-ft)

      G13540097Courtesy of HYUNDAI MOTOR AMERICA
    2. Loosen the two bolts in the corner after supporting the valve body cover on a jack and then remove the valve body cover by lowering the jack slowly.
      G13540098Courtesy of HYUNDAI MOTOR AMERICA
      CAUTION:
      • Be careful when removing the valve body cover because the remaining ATF remains in the valve body cover.
        G13540099Courtesy of HYUNDAI MOTOR AMERICA
      • When reinstalling the valve body cover, replace the gasket (A) with a new product.
      • After installing the valve body cover, make sure to check the oil leakage at the connection area with the engine ON.
        G13540100Courtesy of HYUNDAI MOTOR AMERICA
  5. Remove the valve body assembly (A) after loosening the bolts.

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13540101Courtesy of HYUNDAI MOTOR AMERICA
  6. Remove the E-module (A) after loosening the bolts.

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G13540102Courtesy of HYUNDAI MOTOR AMERICA
    NOTE:
    • When installing, after mounting the E-module, lightly tap the connector part (A) to insert the connector certainly and then tighten the bolts.
      G13540103Courtesy of HYUNDAI MOTOR AMERICA
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.